hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi,
I started with the Blinky example and have added peer_manager to the project by referencing the hrs example. Everything is building, but on init() I am getting a hard...
I have two custom pcbs containing the nrf52832 chip with the EXACT same hardware and software.
When I program and run the old pcb,
The old pcb runs OK. It returns from...
I use SDK 15.3 and SD S340 v 6.1.1. Bootloader is designed to do custom update through GSM; code based on secure bootloader ble example from SDK. I have used code that previously...
Hi,
Greetings!
We are using following setup
nRF52832 DK
SDK16.0.0
Mesh SDK 4.0.0
Light Switch Server and Client
Here we would like to understand below things...
HI,
I set RTS,CTS to disconnect in the overlay file.
(Toolchain Manager.0.6.1/NCS1.3.0)
&uart0 { rts-pin = <0xFFFFFFFF>; cts-pin = <0xFFFFFFFF>;
};
warnings occur...
Below are the details of my setup configuration:
SDK Version: 11.0.0 (with changes corresponding to hardware)
Soft-device: s130_nrf51_2.0.0
Boot-loader: nrf51422_xxac_s130...
Hi, I am Working on nRF52840 and using nRF52840-DK.
Below is my working environment SDK - nRF5_SDK_16.0.0_98a08e2 ,
IDE - Segger Embedded studio (windows 10 - 64 Bit)...
Hello! I gonna buy a NRF52-DK. The seller says the following about kit version :" Hello, original imported. The latest version of 2020. 2.1.0 version". Is it correct? I can...
Hi
In my application, I use nrf52811 to relay data to make the data go further. If data is sent from point A to point B, point B receives the data and then forwards to...
Hi, I'm currently implementing AGPS on 9160, nrf connect master branch. Right before every GPS search we are connecting to our own server via CoAP. To minimize data usage...
Hi!
Running the Asset-Tracker routine will fail to connect to the cloud(ncs1.3.0). The serial port displays an error say Failed to connect to cloud, error -7.
Error...
Problem1: I measured the clock of nRF52840's qspi, is it ok? Frequency is 32Mhz.
Problem2: When I changed the clock frequency of nRF52840's qspi, but it didn't change...
Hi,
After setting up the toolchain, I tried to load an example code on SES, here are the options I used:
But I always receive this error:
The path to west seems...