I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
Hi,
We have developed a nrf5340 custom board powered 1.8 V. So we cannot use the nordic DK board to program it.
I would like to know if there is an interface other than...
I have an application where I am using the SAADC to take ADC samples. At any point during the measurements, I want to be able to stop the samples prior to the ADC buffer filling...
Hi,
I trying to adapt the ble_app_multilink_central example to allow more than 8 peripheral connections to the central device. However, when I change NRF_SDH_BLE_TOTAL_LINK_COUNT...
Hi Everyone,
I am trying to develop a simple application with the XIAO BLE Sense device, the idea is to send a BLE message when something hits the device. To achieve this...
Hi,
I am using nRF52832 board and I want to understand the current consumption in the board will differs while running the code in zephyr RTOS platform and without zephyr...
Hi,
I would like to know where Matter's commissioning ad timeout is set.
I understand that it stops after 15 minutes, but I don't know where it is set.
Best regards...
I am currently learning nRF52840 , I started the BLE fundamentals course , and this the lesson 1 exercise , It Worked Fine , after the lesson 1 , none of the lesson's exercises...
Hello, I want to update the firmware(FOTA) of nrf5340 using AT Command of nrf9160.
I've already reviewed the content in the dev academy below https://academy.nordicsemi...
Hi,
I'm using nrf9160 MQTT at commands to send real-time data to the cloud. I run into the issue where the MQTT publish may fail (frequency varies around 1 out of 500 publishes...
Dear, I'm developing on nordic 52840 with ncs2.6.1.
I found that the Current will reach to 600+uA in k_sleep state by enable SPI in device_tree and if i disable the spi...
Generally, the peripheral calls the sd_power_system_off() function to enter power off mode. Then use GPIO interrupt to exit the power off mode and connect to the central device...
I was going through the driver files for CS47L63 and apparently I2C is not supported for some reason. Here is the code block I'm talking about
Is there any explicit reason...
Hello,
I've been encountering build issues when trying to include MCUboot as a bootloader for my nRF7002DK project using the Nordic Connect SDK version 2.5.2. Specifically...
Hii,
I am using NFC tag reader to interfacing with nrf52832 board , I am using nrf connect 2.6.0v. The sample file is also given( TAG_READER )
I am using spi protocol...
Hello,
Our setup consists of two nrf52840 devices on custom boards. The devices establish a BLE connection via the Coded PHY (S=8). DLE is used. Connection event time is...