Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
In my last question, devzone.nordicsemi.com/.../can-cis-and-bis-modes-work-at-the-same-time-or-switching-freely , I have asked that if the CIS and BIS modes can work at the...
Hi.
I am using SDK v2.6.0 (Toolchain v.2.6.0). When I open VS Code (v1.91.1) I keep getting this warning -->Bad CMake executable: “”. Check to make sure it is installed...
Hello, I am developing on a custom board with the nrf5340 and programming through SWD using the nrf5340dk. A few days ago everything was running fine and I was able to continuously...
We're having an issue where our nrf52840 appears to stop advertising, and isn't able to resume advertising.
Our device is a custom PCB based on the Thingy91 (has both an...
Hi Nordic,
In my project, I have a NRF9160 and a NRF52832 with a ble host/controller stack over SPI HCI on NCS v2.5.2 As soon as I activate the HCI SPI in my project, the...
Hello Engineer Greeting of the day i am building my product using nrf52833 IC , there are some communication modules connected to the 52833 , i want to cheack lowest power...
i have to interface MT29F4G01ABAFDWB in zephyr rtos but i need help how create overlay file for it(i want to interface it using spi), i already have bare metal drivers for...
Hello,
When we flash the BLE Zephyr project to the external chip (nRF52833), do we need to add the SoftDevice controller .hex file as well, or does the merged .hex file...
Hi!
Currently I have the following application requirements:
Use SPI peripheral to communication with FPGA device. ( NRF5340 [ SLAVE ] <---> FPGA [ MASTER ] )
The goal...
When trying to flash the hello world program onto an Adafruit nRF52840 Feather through a j link it fails with "FATAL ERROR: one or more Python dependencies were missing; see...
In any Wi-Fi firmware that I write with nRF Connect SDK I get this error message in my console logs:
<err> net_icmpv6: ICMPv6 handling failure (-2)
This happens in every...
I'm running into this issue quite often where I have a Build failure. I'm sure to others the way to troubleshoot what the issue is may be obvious, but being fairly new to...
i am having a bus fault somewhere in my code, i am trying to use addr2line to identify the source code line that it heppens at, for some reason it shows as if the adress is...
I am trying to connect two thingy:52 and a Polar H10 heart rate monitor simultaneously to nRF9160 dk, but while building the application I am encountering this error. Can...
