Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello,
I am wondering where the best place to add a transport layer for DFU is? I have both bootloader examples working, but now i need to add the transport layers. On one...
I am implementing SPI communication between the intanRHD2132 (ADC) and nRF52840.
I need to periodically send commands (READ, WRITE, etc.) to the intanRHD2132 (ADC). To achieve...
Hello,
I am using the nRF52840 as modbus client and experiencing some missing bytes during communication (RTU mode) when using a high baud rate (460800). This tends to happen...
Hello, I have a question about how to get commands generated from a client cluster in a coordinator. I am currently developing a hub to control and retrieve data from home...
Hi
I tried to play an audio convert file by NRF52840 via I2S, but the sound output was like noise (incorrect):
This is my config I2S:
The audio file I am using "Audacity...
Hi,
Before, posting I tried this post below, but it did not work for me. It did not print the manufacturing data.
https://devzone.nordicsemi.com/f/nordic-q-a/84753/scan...
I'm using a custom board based upon the nRF52840. The BME680 chip works fine in another RTOS but the zephyr/nRF connect example is throwing errors.
I added a fair amount...
hi
We are conducting SIG certification testing with nRF52832 and DFM.
(CMW270)
The TX test was completed normally.
However, a problem occurred in the RX test.
...
Good morning,
Today for a Brazilian Logistic company, I am developing a Embedded System for Low-power tracking and other features, with a nRF52840 in a RAKWireless solution...
i have developed the VL53L5CX code with BLE nrf52840 and it is working fine but issue i have faced is the USB port Restarted Whenever Firmware Download Process Start below...
HI Nordic support team.
I have a question relate to TX power in ANT application:
- ANT Tx application using: ant_broadcast ->Tx
- ANT Rx application using: ant_continuous_scanning_controller...
I've been running a Central + Peripheral application. I can successfully scan for devices and get the advertising data.
However, when I try to connect, the code seems to...
I am running the Direction Finding Connectionless Beacon sample using my nRF52833DK to transmit CTE packets. I am using the u-Blox ANT-B10 antenna board to receive the CTE...
"I am using ncs v2.6.1 on VSCODE, and the following issues have occurred:
Issues:
- Existing build files are not visible in the application.
- New builds are possible...
The multicell loaction has been working fine for a long time. About 8 days ago, I started to receive an error when requesting the location through "Here"
Any help would...
