here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
We are using the nRF54L15 SoC with FOTA functionality. We have enabled secure FOTA by signing the firmware image and provisioning the public key into the SoC’s KMU. For production...
I'm running the subrating sample (ncs\v3.1.1\nrf\samples\bluetooth\subrating) on two nRF54L15-DK boards.
I'm puzzled by something I can see through my protocol analyzer...
Hi,
I’m working on a distributed testing pipeline where tests are built on one machine, but executed on a separate, lightweight container that does not contain the full...
Hello Nordic Team and Community,
I'm working on a fully automated Zephyr RTOS development environment on Raspberry Pi (Debian Bookworm) targeted at the nRF52840 Dongle....
Hello,
Is it possible to get logs (RTT) from an application started by a bootloader? As of now I don't get anything after the bootloader has jumped to the application start...
While running the BLE HCI USB ( bluetooth_hci_usb ) sample in Raw mode on an nRF52840 board, we observe a bus fault under specific conditions. The fault occurs when the device...
Hello everybody,
I am a research assistant at a university , responsible for maintaining and porting existing student lab exercises from the legacy nRF5 SDK to the nRF Connect...
Background:
My project is using the nrf54L15 with the 48 pin package. I'm using vscode with v3.2.0. The QFN48 package has the following pins bonded from the silicon to the...
I am trying to receive extended advertising from a device on nRF52832 .
I have made the following changes:
sdk_config
# define NRF_BLE_SCAN_BUFFER BLE_GAP_SCAN_BUFFER_EXTENDED_MIN...
Hello
Is there a possibility to build MCUBoot, SoftDevice, Firmware Loader and Application separately and then merge it manually? Or to build MCUboot + SoftDevice + Firmware...
Hello there,
I am working on a project which involves nRF52840 to scan and connect to specific BLE beacon.
So while scanning, nRF writes scanned data on UART. On same...
Hello,
I'm running SDK v.2.8.0 and developing using the nRF5340 Audio DK. I've successfully flashed using the buildprog.py script, and have set up my DK as an Auracast source...
Hi
1. At nRF5340 datasheet page 420, the PDM duty cycle is 40%~60%, any register can tune duty cycle? Or it's nRF5340 variation tolerance?
2. Since our DMIC IM69D128S...
