VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Hello.
I use the bare metal SDK and I would like to generate a GRTC interrupt every 250ms to wakeup my system.
Which resources does the zephyr is already using (GRTC_x_IRQn...
Hi,
I’m using an nRF52810 with nRF Connect SDK v2.5.1. I want to read the internal temperature sensor. I started from the LBS sample and added NSMS to report the temperature...
I'm working on the firmware for a custom board built around the nRF9151 SiP. The firmware is built against the nrf9151dk/nrf9151/ns board target included in zephyr, with an...
HI
I am using nRF54L15 PDK with NCS 3.0.0. In my code, I am using NVS to store data on the MX25R64 flash on the PDK. The initialization code is as follows:
struct flash_pages_info...
Hello, I am currently working on a PDM microphone project using nRF52840 and Zephyr RTOS. I've been testing the official Zephyr sample (located at dmicncs/v2.9.0/zephyr/samples...
I have three questions regarding the electrical parameters of the NRF9151 chip:
For a GPIO configured as output: What is the maximum source current per pin when driving...
Hi,Team,
I am developing the nrf54l15-dk, and the version of my NCS is v3.0.2. Because our terminal device 1 does not support using ble-FOTA, I used another terminal device...
Hi,
We have a custom nRF9160 board with chip antennas for LTE and GNSS. They are Ignion antennas with matching circuits customised to our board dimensions. We also use...
Hello, We are developing an application with nRF52810 based on nRF Connect SDK V2.4.1. The application is utilizing the BLE connection, particularly the NUS Service (emulation...
Hi,
I’m testing low-power behavior on an nRF52811 device.
When SoftDevice is not enabled , calling nrf_pwr_mgmt_run() gives me a stable ~5 µA average with no visible...
I am experimenting with ble_app_uart & ble_app_uart_c using two terminal windows, and I am sending a string of 1000 chars from the central to the device.
Although they are...
Hi Nordic
As information of nrf connect SDK, NCS3.0.0 ble_coex sample at NRF7002 DK can share single antenna for BLE and WIFI protocols.
It only needs to set "CONFIG_COEX_SEP_ANTENNAS...
I’m trying to use the Zephyr software split BLE controller ( BT_LL_SW_SPLIT ) on the nRF54L15 DK with NCS 3.0.1. I understand that this controller is not certified, but I...
I have successfully built an Auracast broadcaster transmitter using an nRF540 Audio DK and can stream to a pair of Samsung Galaxy Buds3 Pro with a Samsung Galaxy Tab S11 acting...
