Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi ,
I have some questions about duf Serial routine that I need your help with:
1. Can you explain the implementation process of " pb_decode,pb_encode " and the file structure...
Hello everyone,
I have a Bluetooth Mesh network of Friend nodes that communicate with eachother and allow message to pash through them.
Currently only a few need to...
Hi I am using the POWER PROFILR KIT to measure the current of the NRF5340. I combined them and set the power select and DUT select on DK and started measuring using the power...
Hello,
I am not able to connect the nrf9160 with NB-IoT to the nRF Cloud using the asset_tracker_v2 or the multicell_location sample. I added the following configuration...
Hi
I have noticed that when I configure any GPIO with "NRF_GPIO_PIN_PULLUP" option, the CPU current is raised by approximatly 200 uA. (It doesn't matter if the GPIO is...
Hello, I have managed to get two NRF5340s linked and measured their throughput. Now I need to change their Output Radio Amplifier Power to test again. And then I also need...
Hi,
I need to enable the ADC read and GPIO pin toggling to happen simultaneously at high precision, without using the MCU resources, approximately 15 us interval. After...
We have a device that is using the nrf_drv_csense module to measure a capacitive touch via the event_handler passed to nrf_drv_csense_init(). Unfortunately, due to various...
The latest versions of MbedTLS seem to have some level of support for TLS 1.3 that the nRF Connect library's MbedTLS version lacks. How can I use a newer version of MbedTLS...
Hello,
I am trying to use Eigen matrix library in a project on the nrf52832.
I was able to compile a very simple example however I get a mem_manage_fault while debugging...
I am trying to connect a low power camera Himax HM0360 to nRF52840 dk. In the camera device specification, it is mentioned that it provides I2C serial interface and full speed...
Hi, I'm just experimenting with my nRF9160 DK and have run into some questions regarding the default asset_tracker_v2 program and how some of it works. I have read the documentation...
Hi!
Basically, what it says in the title.
Datasheet mentions that for 2Mbps mode (enhanced shock burst) spacing should be 2Mhz or more.
Does that mean that number of...
