Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi,
I am working on nRF5 Thread 4.1.0 and I am trying to do implement Thread secure DFU.
I am following infocenter.nordicsemi.com/index.jsp
i have run the command...
We are working on a project in which we have integrated multiple modules and examples like GPS, IMU Sensor, SD card, Bluetooth, etc. Now I have to manually shut down all the...
Hello DevZone:
I can see that they are working on a module with WIFI6, my questions are the following.
Will the module have its own evaluation board or will it be integrated...
Very quick question:
I've created a device which implements the Legacy DFU Service. I've also created an Android Application that I plan to develop to be able to conduct...
My application code running on nrf51822 calls sd_ble_gatts_value_set to update a control characteristic. After 16 times receiving NRF_ERROR_BUSY status from this function...
Hi everyone,
first time posting here for me, let me know if i'm doing it wrong.
I'm currently developing a "modem module" built around nrf9160 and working with AWS using...
Hi,
With the NRF Connect SDK version 1.9.1 it is not possible to setup a Thread Coaps connection.
The DTLS handshake fails after Client Hello with an Alert message ...
Hi,
The below is our requirement for NRF5340
1. we have a DFU application with bootloader as an hex file
2. we have another app say blinky as an hex file
3. merge...
Hi all
My first post. I tried to finish one of Nordic tutorials. I need to use app from nrf connect(v 3.10.0): Bluettoth low energy (I have installed v3.0.1). I have nrf51DK...
got the thingy:91 following the getting started video had the bootloader updated and uploaded the right hex file for lte, the provided sim appears to be outdated so tried...
Hello, I am using the Asset TrackerV2 application (SDK 1.7.1) with the modem firmware (mfw_nrf9160_1.3.1). Recently the following error <err> aws_iot: getaddrinfo, error ...
Hello,
I have been developing on a nRF52832 DK using nRF5 SDK v17.1.0, and am very close to a production ready state. The final program will use soft devices, app_timers...
I want to develop a USB composite device using USB CDC ACM + USB Audio. I am not familiar with USB device protocol, so I hope to have a reference example. My development board...
I use the NCS version 1.9.0 with SES.I build and flsah successfully.I use the antenna array with 4x4,about 16 antennas.
In Tx,i use the Putty to debug serial.there is it;s...
Hi,
I have a hardware that I want to connect via BLE and send data via NUS (Nordic UART Service). I can connect to this hardware via the NRF Connect application on android...
