Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
My VSC install is up to date, no updates pending in the Extensions manager etc.\
When building an app for nRF54L15DK I get a warning about the SDK being out of date, and...
I am using the nRF9151-DK as an SPI slave . The SPI communication is not working as expected, and the nRF9151-DK is not receiving any data from the SPI master .
I have configured...
Hello Nordic Support Team,
I am trying to upload firmware to my nRF54LM20B-DK using the nRF Device Manager application on my mobile phone .
For this test, I started with...
Hi!
I'm testing ubidots, which require a 35 character long username to connect with MQTT. This fails, and mqtt_connect gives me error -12 ENOMEM. The same code works fine...
HI,
As stated in the topic I have found several misalignments/issues in the following setup:
NRF Connect Desktop (v5.3.2) NRF Connect Desktop DTM (v3.1.4) NRF CONNECT...
nRF54L15: system clock stops permanently after a GRTC compare event is lost
Disclaimer
Claude Code (Opus 5) was used to assist with this investigation and with the drafting...
Hi, I just started evaluating the nRF93M1 DK (LABA version) and have questions about the firmware version.The AT+CGMR gives "mfw_nrf93m1_1.4.1", which seems to be a bit older...
We're based in India, developing a custom hardware board, and need to test CAT-M1 connectivity on-device. Since CAT-M1 coverage is limited in India, we're planning to travel...
I need an architectural guide and recommended workflow for setting up post-production (in-field) cryptographic key provisioning on Nordic nRF devices (nRF9160 and nRF9151...
Hi, we would like to create a kind of game using 2.4Ghz emitters . The 2.4Ghz USB Dongle emits and the mobile phone detects the frequency + embed unique ID/code so we confirm...
Hello,
we are currently developing a device based on the nRF5340 using LE Audio.
The device streams audio to a smartphone, where the corresponding Android application...
NRF52840
We are using NCS v3.3.0, however this issue occurs also on NCS 3.0.0.
When using the SoftDevice Controller stack. ie MPSL etc enabled, at times we enter SYSTEMOFF...
Excuse me.
When the customer uses the nPM1300 EK for battery charge‑discharge profile logging, after charging completes at 45 °C and the USB cable is unplugged as prompted...
Yesterday, I upgraded to nRF Connect for VS Code extension version 2026.6.2030 and restarted VS Code, and now no matter what I do, the 'Flash' button in my project just pops...
