Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
Hello, I am developing a custom firmware for NRF52832 controller. I have develop power saving mode using power manage function. Also I have enabled interrupt inside code and...
hi,In SAADC sampling, the upper limit and lower limit of sampling results are set. Interrupt events are generated only when they are less than the lower limit or greater than...
Hey Devzone
Running into an interesting issue with the .zip files on http://developer.nordicsemi.com/.pc-tools/toolchain/ . When I try to download in browser they fail....
Hi
I am using nrf51422 (on the DK) with S130, SDK12, functioning as a central, reading multiple peripherals (which I also programmed),
Some of those peripherals have manufacturer...
Hello, With reference to Case ID: 278209, I wanted to include a driver file, for which I was suggested to add the label/variable "zephyr_library_include_directories(.)" in...
Hi,
I have a strange problem.
When I connect the jlink and battery power on board at the same time,and download the application, it works normally. But when I disconnect...
Good morning.
I have a custom board with softdevice 132 and sdk 15.0.3 where I have configured pin P0.16 and P0.17 for uart (rx, tx). I have read in other posts/problems...
I have written BTLE code that works on the nRF52840 DK using SoftDevice s140. I have ported this code to work on the nRF51 DK and nrf51822 MCU using SoftDevice s130. I use...
Hi all:
on my project,i set
define NRF_SDH_BLE_PERIPHERAL_LINK_COUNT 1
define NRF_SDH_BLE_CENTRAL_LINK_COUNT 6
on my peripheral , i need mtu = 185
on my central...
The application of a device is developed based on ncs1.3.0, now the SDK version is upgraded, the firmware function is developed based on ncs1.5.1, and a problem is found,...
Hello,
I'm in an aging manufacturing space and would like to utilize your sensors, but im concerned the pillars and walls will prevent data from being sent. I read the...
Hello,
I am using Nrf5340 with “Direct test mode” example.
I try to make my nrf5340 kits to be an AoD receiver under the DTM.
Now,I am able to run the example code to...
Hi,
I'm using spim on nRF52810.After I init the spi driver and using APP_ERROR_CHECK(nrf_drv_spi_transfer(&spi, &Command, 1, m_rx_buf, 1)) , RTT Viewer showing FATAL ERROR...
Hi,
Is there a way to control the 1Mhz BLE symbol clock?
We want to use nrf52840 as a GFSK transceiver and we need to control the symbol clock (up to +- Khz resolution...
