VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Hello everyone,
In the Light Control Example of Zigbee SDK 4.1 there is a Light Switch with a couple of button assignments.
Used board: PCA10056
(Light switch) Button...
I am getting a
<debug> app: char val length 22 <debug> app: Failed to initialize characteristics. Error code: 0x04 <debug> app: Unable to create RegCertDataList characteristic...
Greetings,
In the nRF5 SDK for Thread and Zigbee v4.1.0 There's the "Zigbee CLI Agent Example".
Under this example the section "Using CLI to control lightning devices...
Hi, guys
I am debugging the I2S feature on nRF340DK, when I completed the initialization of I2S pins configuration and start I2S, the SCK,LRCK and MCLK pins can produced...
I'am new for this platform and working on nRF Connect SDK v1.6.1 with SES on windows.
i plan to develop based on a sample project. so, for example i select file-->open nRF...
I am trying to run and test the ots example but I am not able to connect to device with the nrfConnect or any other app? Please guide me as to how to check the ots service...
I am doing power optimizations on a custom hardware that has nrf9160 and nrf52833 on it. These are connected via GPIO pins and I use two pins to send interrupts to each other...
Hello. I am downloading a custom board (nrf52810) using the nrf52832-dk board as shown below.
I compressed and managed the project file after taking over for company business...
Dear Team,
We are developing a product based on ble mesh. We are planning to select NRF52840 as master device and nrf52832 as slave device. Slave devices should be more...
In the ble_app_beacon example in nRF SDK 17.02, there are two defines namely APP_BEACON_INFO_LENGTH (0x17) and APP_ADV_DATA_LENGTH (0x15). The former defines length of the...
I am trying to port some code from the nrf52840dk (PCA10056) to the dongle (PCA10059) and everything seems to work fine until an interrupt is triggered. All serial output...
Hey! I have a project with custom board with nRF52833 and I would need help with just getting data from sensor via i2c and sending it via bluetooth to mobile device. For some...
Hey!
I would like to use the nrfjprog executable from the nrf command line tools for flashing the nrf9160 modem firmware. I read some older tickets about this issue and...
I have a requirement to start the MCU with extended non connectable advertisement for few minutes and then activate normal connectable advertisement for another few minutes...
