Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello,
I am working on nrf5340DK board and with sample example central_uart. I wan to find at what speed the application clock is configured and also want to change it...
There are lots of questions in the community related to use of multiple advertising sets. Common answer has been that it is "not support at the moment", see e.g.
https:...
I am using nRF52840-DK as a BLE sniffer. I have set up Wireshark to sniff the packets. Between c entral and Peripheral, there is an authenticated LE secure encrypted BLE connection...
Hi,
I'm working with a modified version of the secure bootloader included in the nRF5 SDK 17.0.0. I'm using an nRF52832 to update an STM32 over the air.
I have two update...
Hi all, I need to use the nRF5340's SPIM4 peripheral for 32 Mbps communication. I see dedicated device's pins are pre-assigned on nRF5340 for SPIM4, ad I want to use these...
We have an nRF52840 connected to a SAM4e over SPI. The nRF52840 is the slave and the SAM4e is the master. The 52840 uses a SPI slave routine based on the SDK17 SPIS example...
Hi there,
When parsing the GPS data from the Thingy91's GPGGA format, I've received invalid from such parsers.
Invalid:
I'm still able to successfully parse the value...
Hi,
We used modem fw 1.2.3 ncs 1.3.0 before and got upto 8 satellites when searching for a fix.
Using latest modem firmware 1.3.0 + ncs 1.5.1 we see no more than 3 satellites...
Hi,
I'm using the nrf52 mesh sdk v5 to make a provisioner based on the provisioner example of the mesh sdk.
During some provisioning, the provisioning process timeout...
Hi
in communication networks, GPS is often us to sync network elements and to get accurate timing.
with nRF9160 MFW 1.3, "GPS time based configurable IO-pin / pulse" is...
Hi!
I am developing an application that starts and stops gps occasionally. I am running the gps in GPS_NAV_MODE_PERIODIC with a timeout of 100s and an interval of 240s....
Hi,
We are having problems with nRF52840 dongle.
Intermittently pc-ble-driver-py throws the error in the subject when trying to open interface to nRF52840 dongle. After...
I got an average DRx power consumption of 415.03 µA for 2.56s in the Online Power Profiler for LTE. But unable to get the average power consumption of eDRx.
In the following...
Dear Community, I'm trying to use both datasheet-announced I2C interfaces, one as slave and one as master. Datasheet: www.mouser.de/.../BlueNor_BM833A_datasheets-1627946.pdf...
I have a BLE central application (a form of BLE to LTE bridge) which I have no choice but to redesign due to the dismal state of the supply chain. The original device which...
