here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hello,
I am using nrf52832 chip and SDK 17.0.2 (Softdevice 7.2.0).
I set the MAC Address as random static as shown below (only relevant parts shown):
ble_gap_addr_t...
We are an educational institution and were hoping to use these in a class integrated with LabVIEW. When we load this up on a faculty desktop and run a simple program, it works...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
My device is a peripheral. I want to connect with two smartphones. At that time, I want to connect under the following...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
My device is a peripheral. Is it possible to connect two centrals at the same time? I think peripherals can only...
What exactly does the power management library? Does it handles all the ongoing processes and shut them down?
Because I did a test with for instance a flash write, and I...
Hi, I want to use TrustedFirmware-M as a secure backend for an application that uses Mbed TLS in the non-secure domain, and this seems to be artificially limited - the MBEDTLS_USE_PSA_CRYPTO...
Hi All,
I am developing one device using nRF52840 based on Zigbee protocol.
Currently I am using nRF52840 Dev-kit and nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8.
...
Hello,
as discussed in the email with Joakim T., could you please provide us a sample of how to use AT command %KEYGEN to generate CSR using the ECC private key? If you...
I am using NRF52840 with SDK15
I am using AES 128 Encryption and am confused on the documentation:
During the encryption operation with nrf_crypto_aes_crypt or nrf_crypto_aes_finalize...
Hello everybody,
I'm currently trying to create a Bluetooth Low Energy Mesh network of multiple nodes that I can control using a Bridge application.
I use a nRF52840...
Hi,
we are developing one prototype where we are using two MCU for different task. we are planning to give common reset button (for customer access) for both the MCU using...
Hello,
I am attempting to create an example project of the Asset Tracker using the NRF9160DK.
I have installed SES using the Toolchain Manager.
I have attempted using...
Hi,
i'm using the nRF5340 DK and SEGGER Embedded Studio V5.50c. Today after starting SEGGER i was asked to perform a firmware restoration for the j-link if the nRF5340 which...
Hi,
I need to use two uarts for the project requirement. UART0 is enabled and working successfully. And I am trying to initialize UARTE, but I am not getting any output...
