Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Dear all:
My problem is described in the following steps：
1. Progranm the SoftDevice 7 (S132) into NRF52832, then program the ble_hid_keyboard example(SDK16) into NRF52832...
I'm using NRF52832 with S132_3.0.0 and the SDK version is 12.2.0.
When NRF53832 was bonded to a mobile phone, I try to use "pm_peers_delete()" to delete the bonding information...
I am looking for a way to start advertising as soon as connection event.
Our use-case is: we have 1 peripheral that's connected on CODED PHY to a central with a relatively...
Hi,
I am using softdevice s140_nrf52_7.0.1. I am trying to send the SAADC calculated voltage over NUS to a gateway. For like 20-30 seconds the program works fine and the...
Hello,
nRFSDK5 v16.0, device nRF52840, Softdevice v7.0.1
I am trying to write some data periodically onto device flash memory using FDS Lib, occasionally I come across...
Hello
I'm trying to reenable notifications on a characteristic from GATTS side
The device is 52810 running a custom service and this is the piece of code where i use ...
I am trying to pair my nRF52-DK with my Fitbit device for testing purposes. I am currently using the nRF Connect v3.6.1 desktop application. I can scan and connect to the...
When I run my code using Segger debugger, all is well and I can read and write from flash with issues. However, when I run the same code independently I sometimes get:
ASSERT...
For an ongoing product certification in China, I need to provide the certification lab with the Direct Test Mode application that is available from the nRF Connect suite on...
Hi,
I'm using the NRF52832, as peripheral, to read data from a HTS221 sensor via I2C.
I'm using the TWI_sensor module following this example , but I want it to enable...
Which digital IO pins on the nRF9160 support interrupt on pin change?
I'm implementing an antenna MUX control routine where the MUX control (3 pins out of nRF9160) depends...
Currently working on an IOT solution based on the nrf 9160 SIP that supports both firmware and modem firmware updates in combination with Zephyr and the nrf SDK. During the...
Hi there,
I am studying the nRF9160 DK with the DHT sample from Zephyr, but I fail to build it as error of "'DT_N_INST_0_aosong_dht_P_label' undeclared (first use in this...
Hi,
I am searching the examples in SDK related to security concepts like pairing,bonding and encryption.
And I found ble_app_gls example in SDK 17.02.
Can you please...
