Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
I use SES for debugging,
the chip is nrf52840 with softdevice 140, sdk 15.3
I ported a project from 2017 and now I'm ready to compile all without any error,
but as...
I try to build and debugg a programm from 2017: SDK15.3 Sofdevice 140 5.0.0.2 alpha plattform was eclipse neon
I switched the plattform to SES because neon sucks too install...
Hello,
We have a custom device using nRF52832 with a MTU of 20 bytes, and for one of the tests we are trying to write 248 bytes to the device with nRFConnect, can the "add...
Hi
I want to download the reference design of NRF52840 develop board, I found the follow address ...
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hello,
I've add gps with supl in a project, as in gps project.
If I try to use only gps, everythinks works, but when I put CONFIG_BSD_LIBRARY_TRACE_ENABLED to true, the...
Hi I am able to choose the nrf 52840 dongle in NRF Connect . However, compared to nrf 52840 DK , I am able to read then save as file/ erase & write / erase all.
With this...
Hello
my setup is s140, nrf52840. it is flashed the open bootloader(usb-serial) , the softdevice and an application and everything works fine, flashing running and updating...
hello nordic
i am working with nrf52832, with sdk 16.0 and s132 softdevice, tough i belive this question is relevant to all anrf52
i work with the twi driver (for i2c...
Hi every one , i tries to call the generic_onoff_client_set function to send a message from the client to the server but this ain't working. Can someone please help me?
...
Dear Forum,
I am looking for an OAM vendor offering a small keypad / pinpad device running on an nRF52 SoC. Should be powered by a rechargeable battery and have mini USB...
Hello.
I want to use the nrf52840 as Bluetooth radio controller which is connected over UART to Linux based ARM host.
We are targetting to use meshctl on linux host...
Hi ,
We are facing a problem with cellular connection in NB-IOT mode on NRF9160. We are trying with the asset tracker sample , but cellular connection does not happen. Can...
Hello Everyone,
I started to use the NRF52832 recently and wanted to use it with a sensor from Melexis called MLX90632. I am using sdk 15.0.0.
This sensor have a library...
Hello,
Currently I would like to add a functionality to Bluetooth Low Energy App (BLE). I have a bluetooth slave device that require a specific sequence of sending string...
So, i have been trying to perform a DFU over serial using the method mentioned here by Hung Bui.
Here is a summary of what i did:
- build and flash mcuboot
- build and...
