void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I would like to add events for button release and button long push to my application. I also want to keep the SDK folder unmodified for easy upgrades.
To do this I copied...
Hi,
In my project, I am using High voltage mode [VDDH] in this case automatically REG1 [LDO] will be enabled. But my question is as per the datasheet i understood that even...
Hi.
I am developing using nRF52820 example source using SDK 17.0.2.
USB and LESC were added using S112.
However, during operation, the following HardFault error occurs...
Hi everyone,
I am trying to integrate the DFU service into my application on order to achieve buttonless OTA DFU but I am not able to implement it so far and I need your...
Hello,
I merged the two projects usbd_cdc_acm_pca10056 (A) and ble_app_hids_mouse_pca10056_s140 (B) by copying all additional contents from A's flash_placement.xml into...
Hello,
I am trying to send data obtained from a SAADC port via BLE using the ble_nus_data_send function. This must happen periodically at frequencies within the Gigahertz...
As we know, NRF9160 supports NB network and has an IMEI number itself. Now I want to know whether I can manage this IMEI number, such as reading, writing or modifying. In...
HI all,I am looking for a help.how to start SPIM RX task immediately delay less than 2us？
I have a SPIM test on 52832 DK board(QFAAE0) with SDK16.0, the MISO pin has connected...
Hello
I have a question about the Bluetooth multipairing function using nrf52832. How do I use this feature? And up to how many connections can I make?
Thank you!
I am going to store some informations into UICR.
In case, wrong data wrote have to correct we need to rewrite it.
I have been searched the forum and the answer shows ...
Hello,
It looks like several people are having issues updating the firmware of the Thingy:91 modem with a simple USB cable.
I personally tried on Windows 10, 8 and 7....
Hello There,
I have problems with the installation of the nRF9160. Started the installation earlier and nRF9160 was detected in nRF Connect/Programmer and I could see memory...
Hi, For my application I was using ESB without softdevice and just recently I wanted to add dfu so I had to add softdevice as well. After adding softdevice I found out that...
