Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
HI ,
I would like to combine the Mesh client role with the Mesh provisioner role. That means, nrf52 application is able to switch between the provisioner and client (privisionee...
Hi to all,
i am developing a project based on PCA10056 dev board and i want use bluetooth and NFC in sametime. separately both of them work fine but when i want use them...
Hello everyone, I am planning to use the nrf52840 with the Fingerprint module (https://www.amazon.in/dp/B07DL2DXJX/ref=cm_sw_r_wa_apa_i_Z.VlCbXSSYVRS ). The sensor interfaces...
I got a new nRF51-DK board. I was planning on using USB to program it.
On the board I see pca10028 sticker. What is this?
Also in the SDK I see pca10028, and other pca...
Im getting this error, but i thing this has to do with some python dependencies, Im getting errors with
pip3 install --user -r zephyr/scripts/requirements.txt and installing...
Hi, I have a defined MACRO which I initialised the values of ble_gap_adv_params_t in main.c. I will pass this to the function to start advertising. I used the example (ble_app_blinky_pca10056_s140...
Currently in memory map nRF5 SDK 15.2 (which apparently is a base for Thread SDK) says for nrf52840:
Bootloader settings
0x000F F000 - 0x0010 0000 (4 kB)
MBR...
The nrfx api includes nrfx_gpiote_in_event_disable/enable , but I haven't found an equivalent of nrf_gpiote_int_is_enabled for a pin. I'm attempting to port an interrupt mutex...
nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_blinky
nrf_gpio_cfg_output(16); nrf_gpio_pin_set(16);
Set P0.16 to high level under the main part of...
There seems to be little documentation on TASKS_SUSPEND and TASKS_RESUME in the SPIM with Easy DMA section of the nRF52832 data sheet. My assumption is that TASKS_SUSPEND...
Hi All,
I am working on ISP1507 which is based on NRF52832. My IDE is Keil V5.26.2.0. I have had the following problem in the UART example (pca10040e) from SDK 15.0.0. I...
Hi,
I have modified the multilink example to work with NUS and connect to 2 peripherals, but I'm facing issues with data transmission. I suspect really low throughput...
Hi
I'm testing the range of a custom sensor (nRF52840) by monitoring the RSSI. I use two receivers (the custom sensor and a nRF840 DK) and monitor the received advertising...
Hello All,
I'm very new to Nordic.
For our product development we are using NRF52832 chip and nRF5_SDK_14.2.0_17b948a stack.
Battery powered device it's so is there...
Hi,
Previously, I have done a board and this board have completely no problem to debug in Segger embedded studio.
I have route a new board, this board is almost everything...
