Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I'm using firmware 1.3.6 and sdk 2.7 for Nordic nRF9160. For the internet connection ppp is being used.
Here are the results:
modem shell:
time wget https://leil.de...
Hi,
as i would like to use the uart shell for production purposes as well (e.g. setting the devices serial number) - how can i turn off the shell at runtime (in order to...
Hi,
I've been working on building and flashing the OpenThread CLI sample in two setups:
Setup 1 : nRF21540DK
Setup 2 : nRF52840DK + nRF21540EK
While I've managed...
I've been working on building and flashing the OpenThread CLI sample in two setups:
Setup 1 : nRF21540DK
Setup 2 : nRF52840DK + nRF21540EK
I'm using NCS v2.6.1....
Is it possible for the nRF7002 to operate in both SoftAP and STA modes simultaneously?
From my understanding of the nrfwifi driver, it seems that this functionality may...
Hello
I'm working with the nRF21540 and the nRF Connect SDK 2.6.2.
I would like to set my TX Power to 20 dBm and also check this value. Currently my configuration looks...
Greetings,
I've been developing a DFU firmware that should update the device through Android. The thing is, the device works, but I changed the advertising name, and it...
Hi,
I'm using the nRF5340 Audio application under NCS v2.5.0 as Unicast client.
I want to use the GATT Caching feature on my application.
How should I implement it...
Hello.
There was a problem with high current consumption when using Antenna 2 in some products.
The failure rate seems to be less than 7%, and the current consumption...
Hello,
I want to combine BLE, ANT+ and Apple Find My in one project.
I have permission to use ANT+ and Apple Find My.
I ran the two examples separately and they worked...
I have noticed that the RESETREAS register does not accumulate flags even though the documentation says it should. " Unless cleared, the RESETREAS register will be cumulative...
I have recently purchased a nrf7002 EK from element14.
I have connected it to nrf5340DK board and tried flashing the Wifi-shell sample application(with the help of video...
I’m not sure if I’m posting in the right forum, but since the EVK-ANNA-B402 uses the nRF52833, I thought this might be the place for questions related to it.
Steps followed...
I am using the cdc_acm example and have added a command to set and read tx power. I am trying to use the following commands for this.
BT_HCI_OP_VS_WRITE_TX_POWER_LEVEL...
Hi,
while using the SoftDevice with MPSL on NCS/Zephyr (nRF52840), there will be a HardFault triggered without using Monitor Mode when a breakpoint is hit.
I understand...
