I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
NRF52840 uses 2.5V power supply. We found that when the voltage drops below 1.7V, even if the voltage returns to 2.5V, the entire system cannot work and JLINK cannot connect...
Hello,
We are using the npm1300 PMIC to run the nrf5340 VDD at 1.8V. If we connect D+ and D- from the USB port directly to the D+ and D- pins, will the USB peripheral...
I am developing a custom nrf5340 board design, that is using the BL5340PA external antenna module to implement the nrf5340 chip in the design. The BL5340 module allows all...
Hello,
I am purchasing a RAK4631 module, and am looking for an alternative for the J-link single step debugger. I saw that this product had a o n-board SEGGER J-Link debugger...
Hi ,
I am exploring the peripheral examples from the nRF5_SDK_17.1.0.
I am testing the example code "flash_fds" from the peripherals. I am able to compile the code without...
According to developer.nordicsemi.com/.../migration_sysbuild.html , the config variable SB_CONFIG_BOOT_SIGNATURE_KEY_FILE and SB_CONFIG_BOOT_ENCRYPTION_KEY_FILE should be...
Hello,
I have a custom board based on a nRF9160 SiP. It uses a shared antenna for GPS and Cellular, based on this : https://infocenter.nordicsemi.com/index.jsp?topic=%2Fnwp_033...
Hello,
Installing a new computer with de dev environnment I am finding that NCS1.9.2 is not in the available releases.
Is there a reason for this?
Thanks for...
Hi,
I have a customer in Guernsey that received one of our Thingy91 hubs and he's not able to connect.
Here is some troubleshooting facts :
- when he moves to London...
Hello,
I just received a new NRF9160-DK board and I am surprised it has the 4 leds blinking all along.
What does that mean?
I have not found any of this in the startup...
I need to use UART0 of the nRF9161 via Tx(P0.27) and Rx(P0.26) for serial communication. There is no CTS/RTS signal.
I used the code from Lesson 5 of the DevAcademy. i...
I'm developing with nrf connect sdk.
I have an peripheral IC with a mcu interface enable pin. This product is very focused on battery life. The peripheral IC has higher...
Zephyr / SDK 2.1.2 / nRF52833, acting as BLE peripheral. My system consists of multiple peripherals, and I want each of these peripherals broadcast its own unique MAC address...
Hi
Is any of this antennas supportet or certified in Norway ? I know thingy 91 use trio mxtend from Ignion.
But is run mxtend certified or do I need to certify it ? Its...
Currently, the nRF5340 Audio is set up and running as follows: In CIS mode, the audio source is I2S
Gateway side: nRF5340 Audio DK I2S settings are default Headset side...
