Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
I tried adding the following settings to prj.config
CONFIG_CHIP_OTA_REQUESTOR=n
CONFIG_CHIP_QSPI_NOR=n
I've also tried to modify the Devicetree to be the qspi part in...
Hello, I have a project sampling a ADC. It has a INT output signaling new data is ready to be read with max sampling rate of 125ksps. I am using the interrupt and then reading...
Hi community,
I'm making a custom board using the NRF52840-CKAA. I'm trying to make a Bluetooth application for this board but struggle to achieve it.
setup:
- Visual...
nPM1300ek version: 0.9.0 I have both "nPM Controller" and "USB PMC" USB connected. I tried powering USB PMC through the computer and also tried a "Wall Wart USB".
I have...
Hi,
I have a device which has different UUID s for the write and read characteristics than the Nordic devices. The device I want to connect to will give out sensor data...
hi,
I am in the process of creating a board definition for a custom hardware we are proptotyping. I follwed the instructions in the intermediate course, copying the nrf5340dk...
I have a device which advertises some services, I want to discover those services and write to those characteristics. However I can only find one service and not multiple...
Hello,
I want to send audio to multiple headset(Readily avaiable from market), So is there any hardware, Software solution avaiable for that.
So, Is there any...
We've had good success measuring power consumption with the PPK2 until now. But recently, it started reporting some hard-to-explain numbers. Specifically, t told me a nRF9160...
Hello everyone,
Im currently using the Thingy:91 with the asset tracker v2 application. As I understand the default mode in this application is the passive mode. Im measuring...
Is the nRF52840-CKAA port impedance for the various transmit power settings (or at least for 8dBm) available?
Alternatively, is the expected port impedance, when viewed...
Hello,
I am building basic board on nRF5340(based on Raytac MDBT53 module) and after "Erase" operation in nRF Connect Programmer I cannot access chip anymore.
Board...
Hi all,
I am working on Fantel BT40F which uses nrf 5340 soc. I have finished my breadboard testing phase with the development kit and now I am working on Integrated pcb...
Before adding ubxlib module repo into nrf/west.yml, I can build any project with mcuboot with no problem.
However, I cannot build any project with mcuboot after adding the...
Hi,
I'm stuck in the loop of calibration. This is the error that I get from Putty:
It says that I get a TX error.
This is the code that I have for bno055.h:
This...
