We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
Good day. We ended up getting a bootloader based on the NRF5 using the Serial Recovery method and a non-upgradable bootloader. The update is coming from a microcontroller...
I'm working on a linux driver for nRF7002 based on the experimental linux driver: https://github.com/NordicPlayground/nrf70-linux-driver . This is being done on linux 5.13...
Is it possible to somehow set a lower charge current than 32mA for the whole charge cycle or force trickle charging for the constant current charge cycle? The issue is that...
Hello Team,
I am using nrf52840 board which supports ZIGBEE . Setup Details: Zigbee_LIGHT_BULB (nRF52840 DK) Zigbee_LIGHT_SWITCH(nRF52840 DK)
Light Bulb Example
I am...
I have a GSM application connecting to MQTT that worked previously refuse to work when I picked it up again to improve on it.
To make sure there isnt a problem in my firmware...
The following settings are required to make I2S compatible with the AK5720VT.
MCLK=12.288MHz BICK=1.536MHz LRCK=32kHz Bit length=24bit
CONFIG.RATIO >= 2 * CONFIG.SWIDTH...
Hi All,
I have recently design my version 2 of my custom board, everything seems to work on the board, the firmware is fully running but i can't see the BLE device on...
Hi,
I tried to send audio with a sampling frequency of 44100hz, up until this point I had been sending the default sampling frequency of 48000hz.
For this I change the...
nrf52840 17.1.0 s140 SDK :- examples/dfu/secure_bootloader/pca10056_s140_ble_debug
We are using nrf52840 17.1.0 s140 DK secure bootloader with BLE debug. We initialized...
Hello,
I am trying to make radio test functions work on my 52840-based board using SDK 2.5.2. After some effort I managed to create a simple test program that partially...
I want to use P0.00 and P0.01 as UART pins. I have shorted the SB3 and SB4, and opened the SB1 and SB2 for using the pin as GPIO.
If I am enabling the " CONFIG_BOOTLOADER_MCUBOOT...
Hey, We are currently plan to start Bluetooth FCC certification process with our nrf52840. We were wondering if the BLE Direct Test Mode sample implements all the necessary...
Dear Sirs!
I need that low power comparator on input AN7 reset controller when device is in OFF mode when voltage on pin drop below threshold.
Controller powered +1.8V...
Hi Nordic team
It was heard that Matter spec v1.3 will allow Matter WiFi device to be commissioned by WiFi directly, but not bluetooth.
Was this information correct? ...
HI all,
So after realizing that I needed to Just-In-Time provision my Thingy 91 in order to add the device to my nRF Cloud account, I began the process described in this...