I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
I am exploring the nRF52832 using nRF52-DK for a low powered BLE device. And for that I am making the System OFF example as my basis for measuring currents of different features...
Hi Sir,
We are the first time to use Nordic BT MCU for our product, we have a trouble to select the MCU between nRF52833-CJAA-R vs nRF52833-CJAA- B -R. Sales told us there...
Hi, we are currently trying to reduce the power consumption on our product that uses an nrf52810.
An 1k pull-down resistor has been used on the SWDIO pin, but I don't really...
Hi,
I am using nRF52833 & nCS for an application development,
I am facing a curious issue where, if i enable printk in nCS build, I am getting SUCCESS on calling device_get_binding...
I'm trying to join two programs that work well by themselves, a saadc program that shows the force sensor value in the serial, and a BLE program that turn on or off a LED...
Hello every body,
I'm now utilizing the nRF9160 to develop several products based on SDK 2.0.0. In my program, I must produce SBOM.
This link below has some information...
I am on project using nRF52832 WLCSP.
What's the pin assignment for SWDIO pin? I want to read the input of SWDIO (as indicated in datasheet it's Digital I/O) and can it...
Dear Concern,
We were developing one of our products using nrf52840. We previously used the nrf-52840 USB dongle for the product. Now we were moving to nrf52840 chip based...
Hi,
nRF5340 + nRF21540, NCS2.0.2, VScode
i follow Working with RF front-end modules — nRF Connect SDK 2.0.99 documentation (nordicsemi.com)
how to disable TX_EN? i only...
Hi,
I am using SDK 16.0.0 and nRF52833. In which TWI (master mode) is not working.
Pressure sensor is connected over I2C. (NRF_DRV_TWI_INSTANCE(0))
Previously I am...
Hi to all!
I'm trying to use the same GPIO to wake up the nrf52810 from system off and also use it to execute some functions. I have this code that is based on the example...
I'm trying to load a program to a custom pcb with a n52832 chip, but shows up this error in the Programmer: Failed to load readback protection status: async task failure for...
Hello,
I am working on a project that modified from ble_app_uart_c, with sdk v16.0, softdevice S140
In my case, I defined an event observer by
NRF_SDH_BLE_OBSERVER(m_ble_observer...
