void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
I am using the ppk II, and I have had a number of occasions where the current displayed on the PC suddenly disappears (see attached). The voltage to the DUT seems...
Hi,
I'm testing the nRF9160 GPS performance with a GPS simulator. I set the output power to -130 dBm and test the nRF9160DK conductively. I made some small modifications...
Is there any guide or sample how to run unity tests on a target device instead of the native_posix device?
In general unity however cmock support on-device testing like...
Hello,
My config: - nRF SDK v17.1.0 - nRF SoftDevice S140 7.2.0 - FreeRTOS Kernel v10.0.0 (Amazon.com)
My project used BLE connection with custom service (based on NUS...
I want to use dynamic memory allocation. After searching these forums, I see the following options:
malloc
k_malloc
nrf_malloc
balloc
I haven't had success with...
Hello everyone I hope you all had a good start to the week. I am stuck with an issue I don't quite get. I wrote code with BLE, FreeRTOS, and GPIOTE as a "proof of concept...
Hi,
I'm evaluating the NCS peripheral_uart example for our needs.
I have an issue with deploying this example to an PCA10040 board. While running the example built for...
Hi All!
I have a problem which i can't really understood. I'm using nRF5340-DK evaluation board, and currently i'm trying to get one of timer (TIMER1 in this example)...
Hello,
I have a Nordic connected to a STM32. The DFU procedure on the Nordic works fine and I am able to upload and run a new firmware in buttonless mode. The Nordic also...
nPM1100 use JEITA profile that has charging range 0-60gc. Most batteries has charging range 0-45gc. Is it possible to limit charging to 0-45gc with this chip, or is JEITA...
Hi,
I am developing a product using the SoftDevcie s140 and SDK 17.0.2.
I have the problem, that the standard FreeRTOS port defines configTICK_SOURCE to FREERTOS_USE_RTC...
Hi,
I have a nrf52832 dk(pca10040 1.2.1), use gpio P0.29, P0.30, P0.31 to connect some external device,
external device working voltage is maximum 2.2v, so I connect external...
While running UART rx and tx calls the uart_callback_set I have set during initialization will stop running. This prevents me from sending or receiving any new UART information...
