Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hello all. Now I am making a BLE network with multiple peripherals and central based on NUS. How could I make data transfer between the central and specific peripherals? I...
Hello,
I would like to develop OpenThread applications that run under ZephyrRTOS for the nRF52840 processor. It appears that there are 3 possible development approaches...
Hello I'm trying to implement the DFU Trigger library into my project. to get following function:
" When the trigger library is added to an application, it allows a connected...
Greetings,
I am trying to get the nRF5340 DK to run on the coin cell battery attached to it. I removed the plastic and the USB cable then I put the "nRF power source" switch...
Hi team,
When we set fast advertisement timeout (uint32_t ble_adv_fast_timeout; /**< Time-out (in units of 10ms) for fast advertising. */) to a value greater than 0xFFFF...
i am using Laird smartBASIC for my programming of the BL653. I cloned the firmware of the evaluation board using the supplied Laird batch files and the J-LinkARM interface...
Hello, I have a question that I can't find an answer to in the documentation. The answer may be somewhere and I am just unable to find it.
My application utilizes sd_ble_gattc_write...
is it possible add dfu service and central uart both into nrf52820?
using D:\sdk\nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_uart_c
SDK_17.0.2
Dear Nordic Bluetooth experts,
In the Android-nRF-Mesh-Library , is there a way to mark a unicast address as used? The reason why I'd like to do it is the following: When...
Hello, All,
I am using nRF9160 for product development and would like to know a few more important parameters:
What is the power consumption of an NB-iot network using...
Hi There,
I want to connect programable pins on nrf52840 chips in the schematic.
Can you tell me which pins are for programming and debugging?
Best,
Gaosheng
What does this error mean?
<error> app: ERROR 3735928559 [Unknown error code] at c:\nrf\modules\nrfx\hal\nrf_gpio.h:492 PC at: 0x00033D23 <error> app: End of error report...
We need to update our app to accommodate Android 12, but the DFU library has not been updated and crashes when we initiate an update.
Full details are in github-bug: https...
