void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
I have an issue when I migrate my app from nrf52 sdk v16 to v17.
I have setup an app with an uart communication, an app timer and a watchdog. All off these (uart and...
We are using the Libuarte - advanced UARTE driver and sometimes see crashes in the uart_evt_handler code in nrf_libuarte_async.c when it gets a NRF_LIBUARTE_DRV_EVT_RX_DATA...
I am interested in developing a Cloud Driver that communicates to my own servers over HTTPS.
Cloud API documentations state that a driver needs to implement a set number...
Can I UART/SPI/I2C on any pin of NRF52832?
- Can I UART/SPI/I2C on any pin of NRF52832 which is mentioned general-purpose I/O pin ?
- Is there any limit on how...
Hi,
Actually we are searching for a chip which has more than one UART channel for communication.
Can we define more than one UART channel with GPIO configuration? Is it...
Hello, I am currently using the TWI in non-blocking mode, however I frequently run into the issue where the code gets stuck on nrf_drv_twi_tx. function at the return result...
Hello,
i have created custom BLE service/characteristic using this ling https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial
So, here i am able to transmitting...
Hi,
I tried running the "chat" example on two NRF52833DK boards, one as a sender sending a "Hello World" message every 500 milliseconds, the other as a receiver, and found...
Dear Support
I try to use Watchdog on nRF9160 DK.
I found the sample ..\v1.5.1\zephyr\samples\drivers\watchdog
From there I add to my prj.conf
CONFIG_WATCHDOG=y CONFIG_WDT_LOG_LEVEL_DBG...
Hi,
I wanted nRF5340 capable of reporting the VDD under-voltage event causing a pin reset through a dedicated voltage monitoring IC. For this reason I put a Flip-Flop for...
I am currently experimenting with moving my request for PSM mode into the "lte_lc_init" routine so that it is configured before the modem is moved to Normal mode.
With...
Hi!
I have previously tested connecting the nRF9160-DK to an external MCU to act as an Serial LTE Modem as per the application description. And it worked
fine. Since then...
Hello.
I use nrf9160 and download ota with aws.
After my board download successfull and return event FOTA_DOWNLOAD_EVT_FINISHED, I do system(0) to reboot.
But it can...
Hello,
what is the raw frame to get a good NRF Temperature Service UUID BLE ?
I didn't get custom data (temperature), just the service uuid 0x1809
Here is my raw frame...
