Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
Hello,
I'm writing software for my own board with nrf52840 and SIM800C modem.
I try to connect to MQTT broker. It works when I have TLS disabled or have TLS with certificate...
I'm building a custom system based on the NRF52832 and S132 SoftDevice with SDK 14.2.0.
Our secure bootloader (bonded) is based on examples/dfu/bootloader_secure_dfu. It...
Hello,
I'm working on a project with the nRF52840 PCA10056 board. I want to use Thread protocol. But I'm not sure if Thread supports Coded PHY, a feature of Bluetooth 5...
Hello, I have a nRF52832 DK and a nRF9160 DK and I would like to establish a Bluetooth connection between them and also send data to each other. How can I do that?
Running the Zephyr LIS2DH sample program on a custom board works fine until I configure it to use the trigger and then it throws the z_arm_mpu_fault() error. It doesn't matter...
Dear Team,
chip- nrF52810
I notice a startup current sequence existing for 26ms and the average value is 600 uA. This sequence is present when waking up from systemOFF...
Hi,
We would like your pointers for our following queries:-
1) Would like to know about which firmware stack we can use for provisioning nRF52840 Nordic boards via nRFMesh...
Hi,
I want to do this with nrf9160:
Transmit data (JSON strings) from the nrf9160 to some receiving end, and measure current profile for different amounts of data. It...
Hi,
I successfully send the status of the button from the Switch board to the Light board in the light switch example in nRF Mesh v2.2. .But how can I send other sensor...
Dear community,
we are using nRF52840 (s140) and nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 to develop a multiprotocol (BLE, ZB) application. Regarding the sending...
Hallo,
I try to use app_timer on the dongle to raise an interrupt every 5 min.
The goal is to send the µC in power save mode and every 5 min, it shall wake up, measure...
In the NRF5 SDK 17.0.2 ble_nus_c.c are two calls to the evt_handler without setting event.conn_handle.
Please find attached a patch to fix this for on_hvx() and ble_nus_c_on_ble_evt...
Hi,
I'm trying to figure out what could make the current consumption difference between your blinky example with freertos and with the timer example ?
Here is my configuration...
Hello, this is my current setup: - nRF52840 acting as NUS peripheral, with properly configured coded phy (nRF SDK) - nRF5340 acting as NUS central, with properly configured...
Dear friend，
I am doing a test like this: 1. Connect the Bluetooth device with the nrf conncet app of the Android phone. 2. The notify (CCCD) is enabled. 3. Click "disconnect...
