void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
modem fw v1.2.0 ncs v1.3.0 custom board
I'm trying to make a one-shot GPS app without assisted data by modifying gps sample app, and doing field test, but have an accuracy...
Hi, newbe here, using Segger Embedded Studios, two nrf52840 DKs, SDK 17.0.0, and a whole lotta enthusiasm! I am developing a custom solution based on the ble_app_uart (central...
Hi Nordic team,
One of our customer try to request the (T3324 = 2 secs) and (T3412 = 20 mins) but the +CEREG notification always return 11100000 for T3412 which is disabled...
Hello all,
I tested adc example code. And i want to change this code with our requirement. But in example code, i am getting alternate values on fixed voltage.
How can...
I continue to successfully upload the Blinkey app via DFU. However, when I attempt to upload my development app it does not start. From what I read it has successfully loaded...
Hi
I am test the DFU function in nRF52840. I want to add a timer to the bootloader to generate a one-second sleep action. But when even I have not started to use the timer...
After enabling both the Macro MESH_FEATURE_RELAY_ENABLED and MESH_FEATURE_GATT_PROXY_ENABLED as mentioned in this link ....
Does the proxy and relay feature work for light_switch...
Hello Support
I have a question about the function " uint16_t otCoapMessageGetMessageId(const otMessage *aMessage); ". I need to know the message ID for my application....
Hi,
I am facing a problem while setting up pyaci on Ubuntu 20.04.
On launching the command:
In [4]: p = Provisioner(device, db)
I am getting:
In [5]: 2020-08-04...
Hello guys,
In our current project, we need to have the ability to copy .bmp images from our PC directly to W25N01GVZEIG TR QSPI flash memory of NAND type. To the best...
Hello, i am new to the whole NRF programming. I created my custom board with a NRF52811 SoC, without external LF crystal. I have been trying to get the device to advertise...
Hi all,
I am working on eddystone scanner and I follow this post to start with. However, I have some problems:
1. The device isn't scanning without any modification of...
Hello Everyone,
I am a beginner and working on nRF52832 DK using SDK v13 and using keil mdk armv5.as a compiler. I build it successfully, but when I loaded the hex file...
I am trying to update the firmware on the Thingy:91 following the instructions here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nc_programmer%2FUG%2Fnrf_connect_programmer...
