void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi Sir
How to config channel and AINx to specific gpio for SAADC ?
For example, if I want read adc voltage from NRF_GPIO_PIN_MAP(0,5), how to set the channel and AIN ...
Hi ,
SDK : nRF5_SDK_15.0.0_a53641a
Chip : nFR52810 【1】Is nRF52810 only use pca10040e （nRF52832 = pca10040 , nRF52840 = pca10056） ? And can't use wrong （nRF52810 use pca10040...
Hello, Nordic
I have to immigrate from SDK14.2 to SDK15. I know that many things have changed in the process.
I'm referring to the Immigration guide but, There is UART...
I am using a PPI to implement a READY line for my SPI slave.
PPI's EEP is set to my SPI slave's EVENT_END
PPI's TEP is set to my GPIOTE's TASK_SET to deassert my READY_n...
Hello,
My previous question is this.
I try to implement sample application with Radio Driver 1.1.0 to SDK15.0.0 ble peripheral uart example.
Symptom
For few micro...
Hi:
I am fairly new to Nordic so please excuse my ignorance. I recently took over a project which used sdk 11 and I am in the process of updating it to 15 and want to see...
Hello,
We are developing a wearable device with NRF52 as a Beacon with CR2032 coin cell battery. We need to measure current profile for the beacon and calculate corresponding...
My environment is:
SDK14.1 + SD132 V5.0 + NRF52832
2 sensors(MPU9250 + LPS22HB) 1 battery gas meter (LTC2942) are mounted on TWI ( +1mA)
SPI to spi flash. (+1mA) and...
Hi，
I use SDK is nRF5_SDK_15.0.0_a53641a
【1】In examples proprietary_rf , Here is only the example of pca10040 , So I have to download a lower version of the SDK ?
（...
Hello, I am trying to setup and use the nRF sniffer (ble-sniffer_win_1.0.1) on my NRF51DK (PCA10028) board. I followed the instructions and using nRF studio, I erased all...
Hello!
I'm currently trying to lessen the current consumption of the nrf8001.
I tried to change the connection interval, slave latency, and the timeout using ChangeTimingRequest...
Hi,
I've been using the nRF24l01+ for some time now and am quite satisfied. I'm having a new issue that I'm unable to explain and for which I would greatly appreciate some...
I have filed an issue related to HCI UART sample from zephyr running on nrf52832. I compiled the hci_uart sample successfully, but I am not able to use the UART interface...
Hello, I'm using SDK 15 and softdevice 6.0.
I use the micro as a master and I connected an i2c sensor as slave. I had put external 10 Kohm pull-ups, but I had a low level...
Hello ,
I am using SDK for mesh, I have saved .hex image file in flash.
Is there any example or any suggestion how can I run bootloader which will read data from flash...
