Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
I'm using nRF Studio Visual Studio Code. (SDK and Toolchain v.2.7.0) with the nRF7002 Development Kit. The Blinky example have worked fine and also the other things as shown...
I'm trying to run the vanilla HTTPS sample on the nRF9161 DK: sdk-nrf/samples/net/https_client/README.rst at 4b9841a28e97e9d61b93f8981375d644b9d04ea0 · nrfconnect/sdk-nrf...
I need to install the Direct Test Mode App to validate the direct test mode running on a custom board. On the version 5.1.0 of nRF Connect for Desktop all app installations...
Hi everybody I'm using nRF Connect SDK 2.6.1. I have my own board based on nRF52840 SoC. I made an overlay file of nRF52840DK and changed its UART TX/RX settings according...
I am trying to use my nRF52840 as a sniffer and am attempting to follow the directions at:
Programming the nRF Sniffer firmware (nordicsemi.com)
Note that I have downloaded...
Hi,
I want to use a LNA for make our sensitivity better, Then i should to put a RF switch and have a control in sending and receiving, because when the device is in receiving...
I am developing a USB dongle (nRF52833) for computers and a controller (nRF52833). As a basic configuration, multiple controllers need to be connected to one dongle. Multiple...
Hi,
We have a custom board (powered by nRF52840 with Softdevice and nRF5 SDK 16) that has an external ADC module to sample 30 kHz ADC continuously for 1-2 seconds. What...
I encountered the problem trying a Matter OTA-update and and asking myself why the bootloader wouldn't apply the image:
I am using the partition manager and defining the...
After flashing the nRF Sniffer for Bluetooth on nRF52840 dongle, I want to flash it back with the programmer to use it in the nRF Connect App but it wont go in boot mode....
Hi. I did some testing with two nrf5340DK boards to check the accuracy of distance measurement with Nordic's nrf_dm app. Even in non-high precision mode the reading with ifft...
Hi.
Our company has a couple of different custom designed boards using the nRF52840 and powered by a battery. OpenThread is used for networking, and the devices are configured...
Hello, I got a custom board based on nRF52840. It uses extended BLE advertising to deliver a sensor data to the central hub with a frequency of 10 Hz. I've set the interval_max...
I have a question regarding DTM using nRF Connect for Desktop. It is my understanding that the signal generated does not have a BLE packet structure but it is a continuous...
