I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
I want to control LED of the Server 2. (Turn on / off) by using Client.
How to add the relay node in light switch example (this is one of the basic example...
I am trying to update a device using a Macbook pro with Sonoma 14.4 and am receiving an error message that states that nordic "Did not receive checksum response from DFU target...
hello, I'm using nrf52DK & connect sdk v2.6.1. I'm in the process of migrating from nrf5 SDK to connect SDK.
My previous code to read Mac address to form unique BLE names...
I am getting a warning in my nrf5340 overlay file because I ran out of pins and need to reassign P0.30 to my BMI270 interrupt 1. Here is the message in the overlay file: ...
I am using visual code studio, zephyr RTOS, v2.5.2 on NRF52840
I am trying to find a QSPI example
I noticed someone mentioned the sample :spi_flash is using QSPI ? But...
Hi,
I'm migrating my application from SDK v2.4.1 to v2.6.1. In my application I'm using Zypher BLE Controller with HCI_rpmsg child image. I renamed the hci_rpmsg to hci_ipc...
Hi.
Can you please tell me how to erase the chip in VS Code without writing new firmware?
In Segger Embedded Studio there was such an option (Target -> Erase All), but...
Hello,
I am currently trying to figure out why my application stops working after some time (can be hours to days).
Im am using a nRF9160-DK, with the nRF91 programmed...
Hello,
I am working on a BLE application based on the nRF52840 and NCS 2.5.0.
I'd like to reduce or disable the packet retransmissions. I've looked through the NCS documentation...
I have a firmware project currently developed in a Nordic nRF52840 chip. I am trying to create a new board ( we are updating the PCB ) to implement the same firmware on a...
I have an existing project with a custom board. It builds from VSCode and command line with ncs 2.6.0. With 2.7.0 it builds from vscode, but not from the command line (see...
Hi all, For this project firmware overview: A few months ago, we shipped 10k products and never had such problems. In the latest order, 38 out of 1k products were abnormal...
When using two 52833 boards for distance measurement, when testing at 60cm, the distance value obtained sometimes wobbles between 0.6-1.2m, but sometimes stabilised around...
Can I use gazell device and ble host on one nRF52840 chip at the same time? If so, can you tell me how to develop it? Or give me an example for reference.
