Hi everyone,
We're reading BAT level by reading data from ADC pin and the setup diagram is shown below.
We tested our device at hospital, and we observed significant...
I want to have two Kconfig flags that are both booleans but the build will fail if both are set. My code below used to work in pre ncs3.0, I'm wondering if there's a better...
Context:
VS Code
NCS 2.9
nRF54l15 custom board
Mac OS Sequoia15.5
peripheral_lbs sample project
Goal:
The goal of this project is to create a bluetooth beacon...
Why project config is not finding relative path of these files but absolute path works fine:
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip-DAC-Cert.der" ...
Hi!
I faced an issue with nRF Cloud Log. If I set CONFIG_LOG_TIMESTAMP_USE_REALTIME=y, I get wrong timestamps (2080 year..) in nRF Cloud Portal for all messages being...
Hi!
We use nRF Cloud Log backend in our project. And during my research I found that it actually doesn't filter (despite the filtering code is there) messages generated...
I am looking for a solution where I can set custom and configurable root Kconfig file via Cmake cache variable, which can be specified through the west build command.
Steps...
I am developing AoA for nRF52833.
Please tell me about antenna switching.
Setting:
PSEL.DFEGPIO[0]=28 PSEL.DFEGPIO[1]=29 PSEL.DFEGPIO[2]=30 PSEL.DFEGPIO[3]=31
SWITCHPATTERN...
Hi folks.
recently I've been experimenting with the nrf7002dk Development Kit, and I'd like to move forward with prototyping a custom board around the nRF7002 + nRF5340...
Hello,
I'm trying to work through exercise 2 of the Nordic Developer Academy. It has me using the Blinky Sample. When I add a build configuration I get an error. I have...
The board is nrf52840 based using mcuboot via usb, mcuboot can be activated using a switch, and is indicated via a led, all setup via device-tree, so no legacy here. Software...
Hi,
I am trying to connect nrf9160 to CMW500 callbox however I am not able to connect to it. Switching to a commercial sim card I was able to connect to the network. I am...
We are finding an issue where after a network is running for a while we are unable to interact with devices beyond connecting to them via the nRF Mesh App. Specifically, we...
HI,
I found that nrf Desktop (v2.9.0 nrf54L15) surport fwupd support, it's same with old mcuboot DFU? and i want to upgrade from SPI, how can i do? is there any demo code...
I have a few questions about the sample source of nRF5340 Audio.
1. Where does the connection processing between the Gateway and Headset take place?
2. Where is the BLE...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-5-serial-peripheral-interface-spi/topic/exercise-1-10/
spi frequency is 1000000 in DTS...
My company is working on a project that uses the nRF53 that needs to wirelessly send out data roughly every 3ms (via ESB). We are now at the point where power needs to be...
In nrf5340 audio application( SDK2.9.0), I try to set phy to 1M in CIS( 1 gateway,2 headsets).
I made these changes：
Add in prj.conf:
In C:\ncs\v2.9.0\zephyr\include...
Hi! I am trying to get the samples "Bluetooth: Direction finding connectionless locator" and "Bluetooth: Direction finding connectionless beacon" to work on nRF54L15dk. I...
Hello,
I'm working up an application where tens of kilobytes are sent via bluetooth to a device which then stores the data on the internal flash (nrf52832). I've worked...
I want to change the Tx power in nrf5340 audio application.
I add CONFIG_BT_CTLR_TX_PWR_PLUS_4=y to prj.conf, but the power didnt change.
How to increase the power ...
