Hi,
I am building an app that connects to the NRF52840 with BLE. The NRF board is attached to an electrocardiogram(ECG) setup, so I am interested in the app being able to...
Hello
I am playing with the mesh dfu and the distributor application on nRF52840 DK board
I load the image I want to distribute using mcumgr application on a Raspberry...
We have devices that have low signal so they have to reconnect to AWS a lot. We have a watchdog timer with a 100s timeout that we feed every 10 seconds in the control loop...
Hello,
I am currently developing a project using the nRF 9151 and SDK version v2.7.0.
The issue I am facing is that I have configured the PSM mode, but it doesn't seem...
Hello Nordic Team, I'm developing an project using VS Code with nRF Connect Extension for an nRF52832 board. The SDK version I use is 2.7.0 , build system is sysbuild . I...
Hi, I'm having trouble running the samples/net/aws_iot sample on nRF9160-based board.
Configuration: - nCS: v2.6.0 - modem version: nrf9160_1.3.6
When running the sample...
Hi
I'm trying to use the nRF Cloud Provisioning Service with the nRF Cloud multi-service sample in SDK 2.6 on a nRF9151DK.
I have got the token from the device using AT...
I would like to create a thread based sensor and use Apple/Amazon/Google smarthome hubs as the OTBR. How do I commission a thread device (not a matter device) to these hubs...
Hello,
I'm working with Zephyr and using MCUBOOT as bootloader.
Due to HW design I have to set and hold a gpio as fast as possible when the application boots (to prevent...
I'm posting some thoughts in the hope of receiving some useful feedback, or at least bringing together information that is currently scattered a bit all over the place on...
Hello,
We're seeing an error that only happens after a cold reboot (unplugging the battery and replugging it) and it happens inside the bootloader while trying to open the...
Hi All,
I am using ' NRF SDK v2.7 + NRF5340 DK + VSCode ' and cloned a official nrf ' blinky ' sample. The code and pins are working fine and I have verified using DK...
Dear all:
I used this command to build light switch for 5340DK:
west build -p always --build-dir nrf/samples/matter/light_switch/build -b nrf5340dk_nrf5340_cpuapp nrf...
Kconfig failed: [Errno 22] Invalid argument: 'c:/users/user/zephyr/kconfig"' is an error that appeared this morning. What is supposed to be in the Kconfig file. I have been...
Hi,
We are seeing issues with Segger Systemview Post Mortem Mode. Original issues were revealed on our custom board with SDK 2.6.1. After enabling the feature firmware crashes...
I have just started using 2.7.0 with the nrf54L15 chips and come across a few problems.
When trying to run the UART sample I found that the app overlay files, which I believe...
Hi,
I'm working on a project using MCUboot, TFM, and a network core app. We use MCUboot with an external flash module for OTA firmware updates.
Recently, we tried upgrading...
I can't remember where I found it now, there was a file somewhere that listed all the files in a project. It had
absolute paths which filled me with dread as it means a...
Hi
I am working on a custom board and have hit an issue with the software part. When the nrf_modem_lib_init function is invoked, it always ends with a timeout (errno ...
Got a Thingy91 (not the x model) that doesn't show up as anything when connected to a PC by USB, except when in bootloader mode, by pressing SW4 (no reaction with SW3) when...
I read other similar issues on this forum but they haven't helped solve my problem. I started with the peripheral_uart example project. Development and execution on the target...
Sorry for long sentence. The nRF5340 document describes about the Reset. This chip set have the POR. so, if POR function work, I don't need to use the PIN reset. because POR...
