HI all,
So after realizing that I needed to Just-In-Time provision my Thingy 91 in order to add the device to my nRF Cloud account, I began the process described in this...
We are using modem firmware 1.3.5 on nRF9160.
When packet loss is high, we sometimes see connection resets (NRF_ECONNRESET) reported by the modem that don't seem to be explainable...
I've been playing around with the advanced_non_blocking_internal_timer example, on my nRF52DK-52832 board using NCS 2.6.0.
I couldn't get it working for what seemed like...
My purpose is to create a beacon that communicates acceleration and heart rate values using BLE.
First of all, I tried to merge the nrf52832 SPI and SAADC sample programs...
Hi!
I use SDK15.0 and s132_nrf52_6.0.0_softdevice
I use nRF52 in two modes- peripherial and central in one time.
When I use it like peripherial and have connect with...
Hi, I want to create a partition setup (for the nRF5340) which I can use with future versions of the nRF Connect SDK, which means future versions of mcuboot and b0n. If we...
Hi,
I am testing two advertising sets on nrf sdk v2.6.0. Legacy advertising and long range. I tried to modify https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples...
Hello,
as part of my tries to use xip on nrf52840, I found that using the entire program on the external flash is impossible due to Errata 216 .
I check the FICR for my...
Hello,
I am needing to use two separate SPI masters, but I'm running out of pins. Are all of the pins compatible with SPI or are there some I should avoid. I'm thinking...
Hi all,
I have an application that is pretty simple. One master that needs to stream small payloads (sub 32 byte) to a receiving device. The payload is a fixed size and...
Question: nRF9161 Getting the high accuracy oscillator (HFXO) outside and sync with other nrf chips?
Basically I want to get the Clock Signal outside on a Pin, is it an...
We have 1 central device and 4 peripheral devices in which one of the peripheral is mobile device if we connect both mobile and other peripheral devices(nrf52840) the central...
I am testing an nRF9160 devkit with a TMP117 I2C sensor. My current goal is to read values from its registers.
My current code uses the function i2c_reg_read_byte to read...
Hi,
I've just received a nRF52840 DK and I'm trying to build and flash the blinky sample on it but the build failed continuously.
I also tried with other sample like the...
I want to convert raw hex bytes to utf8 format. The nRF5 SDK supported this with help of ble_srv_ascii_to_utf8() api. Is there something similar api available with nRF Connect...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I am planning to set up the system as...
Good night,
I am doing the course "nRF Connect SDK Fundamentals" to learn about Zephir integration with nRF52840.
I am developing a RTOS solution based on the RAKWireless...
Hi,
I have an application that each 30 minutes connects to AWS, sends some data and then disconnects and goes to sleep. I have based my aplication on the asset_tracker...
I am trying to use the nrf5340 audio DK for the first time using one of the sample blink codes. I keep getting an error when first creating an application by copying the sample...
Hi everyone,
I'm a bit lost with the nordic documentation. Here : https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/applications/serial_lte_modem/doc/MQTT_AT_commands...