Hello,
I’m trying to get an nRF21540 FEM working with a chip-down nRF5340 design under NCS v2.4.2. I’m able to enable the FEM at its default gain setting, but I hit a wall...
HI all,
So after realizing that I needed to Just-In-Time provision my Thingy 91 in order to add the device to my nRF Cloud account, I began the process described in this...
We are using modem firmware 1.3.5 on nRF9160.
When packet loss is high, we sometimes see connection resets (NRF_ECONNRESET) reported by the modem that don't seem to be explainable...
I've been playing around with the advanced_non_blocking_internal_timer example, on my nRF52DK-52832 board using NCS 2.6.0.
I couldn't get it working for what seemed like...
My purpose is to create a beacon that communicates acceleration and heart rate values using BLE.
First of all, I tried to merge the nrf52832 SPI and SAADC sample programs...
I'm trying to test the RGB led on the thingy53.
Using the sample: C:\ncs\v2.6.0\zephyr\samples\basic\rgb_led which gives errors about the devices error: '__device_dts_ord_DT_N_ALIAS_red_pwm_led_P_pwms_IDX_0_PH_ORD...
HI currently i am using nrf52840 s140 sdk ver 17.1.0 and have added buttonless dfu in the central uart application after running we got run time error and we followed the...
Hi,
I am migrating from nRF51 to nRF52810 and I am trying to set Debug because its not working in Keil5.
I use PCA10028 board and I am connecting my beacon to P20 port...
I have a nRF9160DK board that is used for development of a custom nRF9160 board. The hardware designers have assigned GPIO P0.27 to be a general purpose output pin. This pin...
NCS 2.3.0
nrf5340dk_nrf5340_ns -- problem is in non-secure domain for an app built with TFM.
I have this in my nrf5340dk_nrf5340_cpuapp_ns.overlay:
at compile time...
Hi, I'm currently getting familiar with mcuboot and DFU
First of all, thank you very much for the new Academy course that covers DFU!
If I understand correctly, to enter...
I am trying to get MCUBOOT working with project based on the Audio_DK base, where we need to do firmware update over UART/Serial interface.
I have added the following...
I am using nRF5 SDK v17.1.0.
Is it possible to connect a peripheral device by MAC address, and the device is advertising with a different UUID from the central device? ...
I am using LittleFS for an external NAND flash by using the KCONFIG option CONFIG_FILE_SYSTEM_LITTLEFS = y and managing the driver implementation manually. This has worked...
We have difficulties to get RTT prints from MCUBoot while performing DFU.
As far as I understand Segger RTT is reinitialized when booting Application and this might be the...
Hello! I am using nRF Connect SDK v2.6.0
I'm doing the firmware that will be applied to the custom device.
This device contains one button, to switch on/off the device...
I could use a little help tracking down a linker undefined reference error. I am using nRF Connect in VS Code
c:/ncs/toolchains/cf2149caf2/opt/zephyr-sdk/arm-zephyr-eabi...
1. HI currently i am using nrf52840 s140 sdk ver 17.1.0 i have integrted the secure boorloader /pca10056_ble sdk with central uart after merging i have faced run time error...
I started a project from an example and see that this constant is defined =n in the prj.conf. I am wondering what effect this define has? I can't find any definition with...
Hi
The nPM1300 PS V1.0 page 120/169 gives only the AC specifications of the TWI,
but what are the DC specifications please ?
-VIHmin VILmax of the SCL /SDA input
...