Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Environment: SDK v3.1.1 with a custom board based on the nRF52840.
I wrote a test application that I've been using to verify the hardware on a custom nRF52840 board. I have...
Hi,
We are using an nRF52832 in a bare-metal project. (No SDK)
We have three input channels to the ADC that we wish to use. These must be oversampled. (256x)
To simplify...
Hi guys,
I'm trying to do FOTA updates on my board and I was able so far to download the image but not able to apply it.
I've followed the academy FOTA over WiFi example...
I've got an example code to turn on an LED with a button, it works. When I change it to send an spi command, it doesn't work anymore.
Could you check if you see something...
Using;NRF52832,
SDK17,
Flutter 3.10.5 ,
nordic_dfu : 6.0.1,
iOS 16.5.1
iPhone 14 Pro Max
Using my developer device I can successfully update DFU,
However on...
I flashed the same code to the two nrf5340dk but i get the below output , with out any changes in the example sample code. it gives the serial output every time E: IPC endpoint...
I have installed both sdk 3.0.0 and 3.1.1 but both of them give me the following issue:
Upon building, the error given above shows for some reason but this is not my own...
Hi,Team,
I am currently using the nrf5415 to develop OTA. My NCS version is v3.0.2. Now I have two types of devices: Hub and Terminal. Both of these devices use nrf54l15...
The uart output of nrf52840 dongles is corrupted, including no lines separation, strange characters. for example:
5E0 to 1:00000000148A0C90 [18FF] [UDP:�]�8~~[fdbc:dc24...
I first noticed this when incorrect flags reported by mcumgr when performing network core update
When performing a network core update with CONFIG_SECURE_BOOT_APPCORE enabled...
Hello, I am currently debugging with nRF52833 and nRF5 SDK, and I have a few questions to ask:
I want to time-share the BLE function and the ESB function on a single MCU...
When I2S reads the digital audio sensor, when strat is turned on_ After I2S, the data can be read and recognized normally, but this action takes up the whole CPU occupancy...
Hello Nordic team,
I have a question related to the “nRF5340 Production Programming – Troubleshooting” documentation, specifically the part that says the access port protection...
Per (+) Trouble with nPM1300EK - Nordic Q&A - Nordic DevZone - Nordic DevZone , I've disconnected TWI from the board while doing the battery profiling and that worked successfully...
