I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
I am using nrf9160 custom board with an external flash memory mx25l6433f. I first tested the external flash with the example 'sdk-zephyr/samples/drivers/spi_flash_at45' and...
Hi,
I;m working on nrf52840 dk i have to enable ble5.0 long range.
i set the tx power 8.
according to my project my device will be always in advertising mode and my...
I am trying to scan for BLE devices in my area, but when I connect to the USB840XZ with the windows development tool the "Start Scan" button is not active. There are some...
Hi everyone,
is there a way to update the AWS certificates from certificates.h with the SDK 1.9.99? Following the AWS FOTA instructions it seems that i can update the certificates...
Hello everyone,
I am currently testing the secure bootloader over USB example but I am currently facing an issue when I start a DFU.
Here is my configuration:
...
Hi,
Application details:
I have a datalogger application that samples data every second. It uses the following modules:
TWIM0 -> To communicate with external RTC clock...
Hello,
I am working on application using nrf52810 SDK version nRF5_SDK_14.2.0_17b948a.
Here my application sends 240 bytes of data every 150 ms. But after sending few...
Hi,
I use the a gpiote_in_event to trigger a number of PWM pulses which works fine so far. However, the exact behaviour of the generated signal is important so that the...
Hello, I am using nRF52-DK with Segger Embedded Studio and I'm running the following code that first blinks the LED1 on&off 5 times, and sets up BUTTON1 for wake up, and then...
Hi,
I would like to read the temperature of the nRF.
I tried to use the routine I found here in the forum
Sometimes works sometimes the system crash. I notice the...
Hi
I am using NRF5340 chip in my custom board to communicate serially with an external device whose data length is more than 128 bytes.
The chip can receive 243 bytes...
I am looking for the examples for the SDK. I installed SDK 1.9.1 through the Toolchain Manager and see the directory "users/my_user_name/ncs/v1.9.1" Supposedly this is where...
Hi,
In Openthread's Coap_client sample, Following 2 libraries are there:
and while compiling my code I get multiple warning regarding to above 2 libraries.
Following...
Hi,
I have problem to use bmi160 library with nrf5340 in spi connection.
I use the example application zephyr/samples/sensor/adxl372 and change the sensor to bmi160 (...
