Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi all, im asking question about triggering my own antenna. there's few questions about it. 1. im using TI boostxl antenna array (3 antenna) , periodic table are as follow...
Hi,
I want to use the 64MHz crystal oscillator (HFXO) as the source for HFCLK clock controller. How can I need to enable or disable the item in KConfig on nRF Connect SDK...
Is there a current example for nRF52840 power management under Zephyr / nRF Connect SDK?
Searches for this turn up old examples, such as this one , that are no longer in...
Hi Nordic,
My customer want to know, whether LLPM function and Multilink can coexist?
For example, when I use a central to connect with 4 peripheral devices, can I use...
Hello,
NCS1.8.0 Windows10 X64;
i2s test,see the source code ,
it runing ok;
but,when i change to timer send,got error.
i want to send data by timer,
source...
Hi Team!
I am trying to connect the Thingy 91 to nRF Cloud using a local provider (Vodafone Romania). I followed the getting-started video when setting up my device. However...
Hello,
I need to power the nRF52840 with 1.8V while keeping it connected to SES through USB.
I believe I have to proceed as directed at User Guide paragraph 8.3.5 “nFR52840...
Dear Concern,
We are currently planning a mass production of a product that uses nrf52840 USB dongle as a component. We are thinking of using JTAG debugger to flash the...
Hi,
I am getting a strange issue in my code where my FDS will run fine if there is no bootloader but fails to initialise if there is a bootloader present. I am using SDK...
Hi!
We are testing nRF9160 in an application were we monitor sensor in certain modules on trucks / trailers. Our test application is based on the Serial LTE sample application...
Hello,
I am new to DFU OTA on Nordic's chips and I am currently trying to implement it on a custom board with an nRF52832-QFAB chip.
This will be a long issue since I...
Dears,
I can't select a new operator among the list I have, when I put the command at at+cops=1,1,"20820" , I have the error: ERROR: -8 , could you explain me what is this...
Hi, I am facing an issue, I am developing nRF9160 based Product, get sensor data from peripherals and publish to AWS cloud.my firmware is based on AWS IoT sample. I observed...
Hi,
With my company we want to develop an embedded application with Direction Finding. Do you have any examples to give us to start the development? For this project we...
Hello. I would like to ask a question about a problem I had in implementing the battery voltage monitoring function.I am trying to read out the battery voltage using the following...
