I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello, All,
I want to ask about the modem upgrade of nRF9160.
At present, there is no problem with the minor version of the differential package upgrade.
Can the upgrade...
Hello!
Thank you for the excellent SDKs and documentation on the NRF52. I am developing several user devices on the NRF52 DK PCA10040 and my own boards using the Garmin...
Hi,
I am trying to receive packets from a device with Zigbee custom profile. Through sniffer, I can see that the device joins the network and sends packets on it but I cannot...
Our board doesn't have LFXO, but I want to run DTM. When I try to switch to LFRC by changing sdk_config.h, it doesn't take effect.
chip: nRF52832
SDK: nRF5_SDK_17.0.2...
Hi, we use the Fanstel BT40 design a RS232 & USB carrier board, when we use battery 3.3V to VDD, there is a DC2.8V output from VDDH. VDDH should be power input, why there...
As known in SDK nrf there is a function battery_level_in_percent() used to calculate battery percentage but it is only true for the CR2032 battery. Currently, I am using AAA...
My application uses a SPI LED driver, which I routed on a PCB to the most convenient pins for routing.
I have already tested my firmware on a nRF52833 DK with an Arduino...
Hello, I'm a beginner at developping nrF52832. My problem is completely similar to this one : devzone.nordicsemi.com/.../add-saadc-peripheral-and-others-to-example-project...
I am trying to measure single-phase mains voltage (240v, 50Hz) by stepping down the voltage to 200mv using a voltage divider and read it with the ADC pin of the controller...
Using NB- IOT JIO SIM in india, not connecting asset tracker Work Up to RRC Connected and stuck there. This is custom code very similar to asset tracker example. We are using...
Dear Sir.
Using the mqtt_simple project , I inserted a 1 sec timer.
Within the timer I want to use the publish routine like this
data_publish(&client,MQTT_QOS_1_AT_LEAST_ONCE...
Hello everyone, we are developing a heart hare accessory for the phone and we want to show the battery status directly on the phone. I found it can show up in the Windows...
Hi, I run nRF5 SDK 15.3.0 with SES 4.30c on a PCA10040. Yesterday I upgraded to nRF5 SDK 17.0.2 and SES 5.60. When I connected PCA10040 I got a message that something wanted...
Hi everyone,
I write a firmware to read the values from a 6-axis IMU and some force sensors. I want to sample with a frequency of 100-200Hz, to store the data in a buffer...
