Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi,
I'm little confused regarding BLE NUS and characteristics.
I know that the characteristics are used to expose data, but we also have BLE nus which is used to send...
Hello,
I have 2 questions:
1. Could you tell me the current consumption of a nRF52832 running RTC with external 32 kHz crystal and no RAM retention? Is it 1.9 µA?
...
Hello,
I use nrf52840-dk as central_hr and nrf52833-dk as peripheral_hr, examples from NRF Connect SDK.
It works well, but I want to implement reading Device Information...
I got following error when use the Command Prompt feature
After i run "ncsmgr init-ncs" from bash, it shows
$ ncsmgr init-ncs Checking out NCS v1.6.0 ...FATAL ERROR...
Hi,
I'm developing with 52840 DK, trying to add peer manager to another project I've modified from ble_app_uart (basically I've added saadc, SPI, USB and I2C module based...
Hello
I was setting up the nordic thing 91 (1.4.0, 2020.23) using this video https://www.youtube.com/watch?v=xQ7hDzRULJQ&ab_channel=NordicSemiconductor .
Things were...
I'm starting to design a custom board around the NRF52820 using a 3.7v battery and there is no reference circuity for VDDH using Battery/Ext. regulator. Any tips on what I...
Hi,
We are in the process of evaluating coded phy transceiver for our next product. The product is a IoT node which will send sensor data to centralized gateway and will...
I am using nrf_drv_twi_rx to initiate an I2C read transfer but the interrupt isn't fired for the RX transfer when the ulTaskNotifyTake is used, but seems to work without ulTaskNotifyTake...
Hello, I am making a system with 20 peripherals to a central base on nRF52840. I followed the firmware."ble_app_uart__saadc_timer_driven__scan_mode" from NORDIC playground...
Hello, i I am designing a prototype, the goal is to be able to control a small engine. This engine will be activated when a message is received in MQTT. I currently succeeded...
Hello, I developed for my customer, a ZigBee coordinator in last 2019, using nRF5 SDK for Thread and Zigbee v3.2.0. I have now two questions: - is ZigBee 3.0 supported by...
I'm currently working on the nrf52832_qfax_dcdc pcb after adding a few components. I need to route to pins p0.22, p0.23 SWDIO and SWDCLK but am unable to route away from the...
Hello,
I noticed that publishing mqttsn messages with a payload larger than ~255 bytes caused an error in the mqttsn library. I think the problem comes from this definition...
