I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
HI,
I'm facing a weird issue where the nRF52832 breakouit would reset and upon reading the RESETREAS reg, the value is 0xC or 0X8 ,I am using s132_nrf52_4.0.2_softdevice...
Hello,
I am using nRF52833, nRF Connect SDK v1.4.2.
I have imported the Zigbee light switch, light bulb, network_coordinator build and test it successfully.
I have also...
Dear Sir/Madam,
I have bought NRF52840 dongle to bring up my prototype as fast as possible. I am new to Bluetooth tech.
My application requires following peripheral...
Can we do CTL with dimming and generic on/off in nrf mesh app simultaneously. by using GPIO pins p0.15 and p0.16. for external leds. Is external led will get off. What will...
Hello there,
I am using nRD52840 PDK and nRF5_SDK_for_Thread_and_Zigbee_v1.0.0 SDK for BLE and Thread development. I am using examples from SDK. I have merged thread coap...
Hi, I am working on implementing the security aspect of our BLE application using nRF52832 MCU with SDK 17. The goal is to establish a secure connection between peripheral...
Hi，Dear all:
I got trouble when I change “libuarte example”(nrf52840 DK, SDK17.0.2)，the default example use RTC instance :
NRF_LIBUARTE_ASYNC_DEFINE(libuarte, 0, 0, 0...
Hello Nordic Team, Over the course of development I have had to reverse engineer and pick apart various sources (DevZone, Google, Zephyr documentation, etc) in order to figure...
Hello Nordic
I am using nrf52840, SDK 16.0,
I wish to implement Ble peripheral that advertise a connection request (if no response from central after x seconds then...
Hi, I am integrating BG95 with Nrf52 and have been able to achieve the a basic serial communication, but for a stable application code to handle all the AT commands, I need...
Hello,
I have been recently working on a project that involves transferring potentiometer data from an MCU to the NRF52832 and receiving it over Bluetooth. (MCU-->NRF52...
Hi,
I have using nrf52832. I have done the device sleep by using RTC. But, it's not wake up from sleep. How Can I wake up the device from sleep?
I need help regarding...
I'm facing a rather strange problem with an nRF52832 board I'm developing for. I'm using SDK 15.2 and S132 v6.0.0.
Sometimes, during the connection/negotiation phase, my...
Hi,
Is switching from softdevice S210 to S310 as simple as changing the IRom start address and putting the uploading the softdevice onto the device?
Now I have IROM1 start...
