I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi community ! All is in the title.
The latency between sending the message and receiving the callback is not stable ( between 1600 & 4300 ms) I know that this delay is...
Hello, guys!
We are currently developing our firmware with nRF9160-DK and nRF Connect SDK v1.3.0. Among the other things, we need to communicate with the ultrasonic sensor...
Hi,
As we are in design phase of our custom board based on nRF9160, can you please let us know what all pins needs to be exposed in our design for collecting modem traces...
Hi Team,
I am trying to integrate a scheduler feature for my Thingy 91 using a nRF9160 DK kit. I searched for a few examples and found the one below in the link:
https...
Hello everyone,
I am developing a simple BLE node with an I2C sensor on it. Basically I just need to send over BLE the measurements made by that I2C sensor every minute...
Hello,
I am new to the Nordic environment and am trying to set up a beacon to scan and advertise using BLE.
I used the beaconing example ( https://github.com/NordicSemiconductor...
Hi, I have the same issue as in here: https://devzone.nordicsemi.com/f/nordic-q-a/62676/2-spi-devices-nordic-nrf52382 but for me the Debug/Release-toggle does not work. I...
Hi,
Can you confirm if TWI is supporting I2C clock streaching? Or and workaround to handle such a case.
As in attached picture is slave device requirements. Slave device...
Hello,
I’m using keil compiler.
My configurations are nrf51822ac/SDK12.3/s130_nrf51_2.0.1_softdevice.
I’m trying to migrate to SEGGER studio.
I’m referring to the...
In my case, I have 50+ devices as sensor and advertising measurements every 10 seconds, ADV_DURATION = 120s, use the 1E FF manufacturer data and self defined payload protocol...
i want to implement the nfc connection of pairing the nordic nrf52840 using SDK ver 15.0.0.
Can anyone help me in implementing this feature? because I'm new to this pairing...
Hello, all
I would like to ask about flash memory write errors.
When using version 12.1.0 of sdk, I was able to r/w to flash memory normally by using the sd_flash_write...
Based on sdk12.3, use 51-dk (51822) to run the ble_app_hrs routine. Use ios mobile phone to connect the device, it will automatically disconnect after 30 minutes, the disconnection...
The problem is not being able to connect to the device from an iPhone SE while the app is in background mode. We have an iOS app written in swift, which uploads data from...
Hello, I have couple of NRF52840 devices that i purchased from Adafruit. I wanted to use them with Alexa Gadgets Toolkit via BLE, however with no previous experience with...
