I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi All,
I'm working from the Thread CLI example, and I got a network of multiple thread devices that works just fine (they see each other, and can send/receive messages...
Hi there,
I'm trying to do a basic test with the GPIO/NMOS - just trying to turn an LED on and off for now. We're going to be doing this in response to the outcome of an...
Hello,
I'm working on the mqtt_simple sample in zephyr environment for NRF9160 board.
We tested the firmware with 2 sim cards with different packets: IPv4 and IPv6,...
azure_iot_hub_connect does the following check:
connect_client looks like this:
If the embedded return at line 40 of connect_client occurs (as I've seen it do) then...
I noticed on Zephyr docs this:
nRF5340 PDK (preview development kit) is an earlier version of the nRF5340 DK. nRF5340 PDK board is deprecated and is replaced by nRF5340...
Hi Nodic,
I try to add the tx power to both the connection mode and advertisement mode to make it long range available. But when I run the code it fails.
Please check...
Hi.
I do not find the description about I-Cache principles and work algorithm.
I read the part of the documentation "NVMC - Non-volatile memory controller". I think, I...
How can configure NRF_LOG_UART to use UART0 or UART1 for nRF52840? I cant see any configuration which uart NRF_LOG_BACKEND_UART will use
As per spec nRF52840 should have...
Hello,
I want to develop a new IOT product using the NRF52840. My device will be using the MCU with BLE and a very low power sensor.
I want to use a 3.7V one cell battery...
Hi,
I would like to input a data(integer) into the CLI and store the data. How can I do that. I have seen SDK but could not find any function or macro.
If there is any...
Hello, Not sure if this is exactly the same as what is happening in this case , but the issue of an early disconnect when NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 247, can simply be...
Hello
I would like to retrieve the signal strength of the Thread messages I receive. To do this, I used the otMessageGetRss (message) command in my request_handler but the...
I have cloned a few beacons with nRF Connect and use the app to advertise these when testing our beacons and apps. It is (to my best knowledge) not possible however, to export...
I have been trying to use the secure services to read random from the CC310 and have been getting unpredictable crashes. I have been able to modify the secure_services sample...
sdk ncs v1.3.
Example name: serial_lte_modem. Example path: D:\ncs\v1.3.0\nrf\applications\serial_lte_modem
The error in opening this sample macro definition is as follows...
