We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
I want to connect and get data multiple peripheral to a single central device.
I used this example https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
...
I can't figure out how to respond to a custom Zigbee cluster command, let alone send a custom response. Is there any example on which I could understand how to send a command...
Hi!
we're just finishing the layout for a custom nRF52832 board. On the custom board we have a connector for SWDIO and SWCLK to flash the firmware. Can we use theese 2 pins...
Hi,
I'm trying to familiarise myself with the available crypto functionality on the 52811 and have managed to get basic AES-128 block encryption working using the ECB peripheral...
Hi,
I am using pc-ble-driver-4.1.1 to receive BLE peripheral Device 240 Bytes notifications. And I used "pc-ble-driver-4.1.1\examples\heart_rate_collector" as starting point...
Hi Nordic team,
we want to connect 2 nRF52840 based modules with Coded Phy S=8 Mode to make an cable replacement (NUS). MTU Size is 244 Byte ,to transmit cyclic 200 Byte...
I am trying to connect the DK to AWS.
I got the AT example working and uploaded the certificates. I managed to update the prj.conf file (and then took quite some time to...
It continue to give "No device available" when I connected thingy 91 to the nerf connect programmer app. I tried turning on device while keeping SW3 pushed but still not detected...
Hi Team,
We are planning use the crypto libraries for our application, just we want to know which library is best for us in terms of speed and memory consumption,
1. mbed...
Hi, I'm almost finished setting up a development environment for nRF52840 DK on macOS. I used the new Toolchain Manager to install everything, and then imported the "peripheral...
While developing our project using NRF9160 , we encounters a hard fault. The screen shot and the map file is attached. Please help us in understanding what is happening from...
Hi, we are using nRF52832 SAADC in differential mode. We have two channels connected.
Inputs are now configured as differential-N and differential-P (PSELP and PSELN). ...
Dear all:
i have a problem about connect distance. My central device is nRF52840 ，peripherals are nRF52810 device。all device Hardware RF performance are good. But,when my...
Hi In continue to Tzvi Kaplan thread and other threads here related to the PDM, like this one:
devzone.nordicsemi.com/.../single-pdm-microphone-at-higher-pcm-sampling-rate...
