We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Hi,
I'm trying to add the NUS service to an existing application (freertos based, SDK15.2, already use a custom service)
I copied the relevant code snippets from...
Hi everyone,
I'm trying to use nRF52810 with SoftDevice S112 to sample five ADC channels. I'm finding this very weird issue, where first channel is showing correct value...
Just getting started with Nordic toolchain and I got this error below.
=== updating civetweb (modules\lib\civetweb): --- civetweb: cloning and initializing Initialized...
i need a code for when button press after one second delay led will glow continiously whenever again pressing the switch it will stop glowing using apptimer
Hi, Everyone
My development environment is sdk15.3, nRF52840, Keil complier
The link error file is attached below.
Also I am going to use AES-CBC method.
Which example...
I'm experimenting with the USB MSC example (SDK 15.3) on my nRF52840 DK. It seems to work well in the polling mode as delivered. However, when I try to run in interrupt mode...
I have a serial port set upp with the serial port library like this:
#define UART_PIN_DISCONNECTED 0xFFFFFFFF /**< Value indicating that no pin is connected to this UART...
Hello,
I am trying to get started with the 9160-DK. So far it does not seem similar to the 52840 so I decided to take to the "Getting Started Assistant" within nRF Connect...
Hi, I'm using nrf52832 and SDK15.3. And I'm using the ble_app_uart example. The device will go to sleep mode if there is no connection for 3 mins.
My questions are:
1...
I'm calling sd_ble_gap_adv_start after a connection disconnects to start advertising again and it's returning err_code 12... which is NRF_ERROR_DATA_SIZE. However, the documentation...
Hello,
I am currently working on a project that involves the host device to send configurations parameters over to the device. I was hoping the connection between in device...
Hello All,
We working on OTA features with nRF52810 using sdk16.0 . When we are trying to upload the firmware zip format through mobile its giving error "upload failed:Insufficient...
Hi,
I am new at mesh .I use SDK UART coexistence example to test, and I can scan Ble uart demo by nrf Connect APP. But I can't scan Mesh node by nrf Mesh APP. I've been...
I am trying to program the Nordic nRF51822 MDBT40 Series module to communicate to an STM32 processor chip. The way I understand the procedure is as follows:
First, I must...
