Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Good afternoon,
The 'sd_ble_gap_device_name_Set' seems to have a limit of 10chars when defining the device name. In principle, it should be 31. Why do I have this limit...
Hi
I would like to use a 2.4Ghz remote controller for a project but I did not find any example/documentation on how to use 2.4 frequency with my nrf52.
Can someone...
Hi
I would like to use a 2.4Ghz remote controller for a project but I did not find any example/documentation on how to use 2.4 frequency with my nrf52.
Can someone...
nRF52840-DK 2pcs, one TX broadcast signal software, one RX software. RX can receive TX.
My nRF52840 product 2pcs, one TX broadcast signal software, one RX software. RX can...
Hi,
I am working with a motion sensor which sends a message when it detects a motion. I am communicating between the nRF52 DK and the sensor via UART. I am able to receive...
Hello,
I am interfacing nRF52840 DK with the MAX30101 sensor. I am able to execute all the TWI transactions necessary by using port 0 pin 27 as SCL and port 0 pin 26 as...
Hi,
As background, what I am trying to implement is continuous uninterrupted SPI master output from the nRF52840, compatible with the MCP4822 two-channel 12-bit DAC. The...
Hi. I have some question.
I'm using Mesh with nRF52832.
How get address after provising?
Is there API function?
1. get or set address -> Unicast address.
2...
Hello,
I am trying to configure a Heart rate sensor MAX30101 with nRF51822. I have initialized the sensor correctly as I can see the LEDs turn on. But when I read data from...
Hi, guys. I'm trying to work with Opus applications using PCA10056 v1.0. In order to play Opus fils using the nRF52840,
do I need audio DAC + audio amplifier to create sound...
Hi,
I am using NRF51822 pca10028 UART ble example ,
I need to give provision to change the name of the device after pairing and reset the device so that it starts advertising...
Hello,
I m bonding a central and a peripheral and saving the bonds into a whitelist i use at each startup. When i delete the bonds on central side, the connection to the...
I am using a ultra-miniature (BMD-350) series module from Rigdo which has the nRF52832 BLE SoC. The pins from the nrf52 SoC are all brought out on a female headers on a custom...
I am running a custom board (Ublox Neo dev board) and have a custom board file.
I have modified and and can run code in Segger Embedded Studio based on the peripheral serial...
Hi,
I'm getting a Hardfault MemManage (IPSR 003) when calling sd_ble_gap_adv_stop(). The advertising handle I'm passing is 0. This is called after the advertising has started...
