I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
Dear all,
I am trying to adopt the flash_fds example to fit my needs. What I initially need to get sorted out is how can I erase the memory pages after I have fully written...
hi, team.
I've got a question. I use nrf52840 dev board. There is a connection between nrf52840 and ds18b20. I tried to use dedicated HW timer to count delay according to...
Hi team,
There is connection between nrf52840 and ds18b20. I have made simple lib for ds18b20. When i get temerature without softdevice (s140) all works correct (use 9-bit...
Howdy,
I'm trying to access the SD card on my device via the usb MSC and am not sure the best way to proceed.
I have a custom board with an nrf52840, and it works great...
Hi,
I would like to make development on nRF52840-DK by using Segger Studio.
However, I could not find detailed document that specifies how I should start development...
Hello all
I was just following the thread launched by Alex concerning nrf 52 dongle driven from serial port, which is also very important to me, and now that thread is already...
Hi,
i would like to program my module nRF52840 via uart.
I generated private then public key using nrfutil.exe tool
i could programm softdevice and bootloader and...
I am trying to get the DCDC running on my custom NRF51822 board.
It is running but the results are a bit disappointing.
If I do a test and enable the TX with and without...
I've picked up a nRF52840 DK and dongle to do some testing with long-range beacons.
So far I think I have managed to configure my DK as a beacon in long-range mode (can...
Hi
I have a test mesh network, with several devices provisioned using nRF Mesh and.... a proxy node which has been provisioned using an alternative method but with the same...
Hi, I'm trying to make a SIG qualification Project. QDID97989 (nRF52 S132 V5.0.0) with replace PHY QDID97482(TaiyoYuden module). Launch Studio Project type is "qualification...
How to send and receive messages in ble mesh? The sending and receiving of sensor data I have done is not a switch value. I have tried many methods but failed.
I alredy run the assert tracking about 4 months ago on preliminary firmware.
Now I updated the modem firmware to v1.0.0 and compiled the last stable AT Client project from...
In the past we had a C based product that communicated from our Host processor over SPI to an nrf8001 peripheral using an Application Controller Interface (ACI) provided as...
