Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Details: SDK v15.2.0 using peripheral spi example. Windows 8.1, uploading to nRF52 DK.
When I upload the example as is my clock , MOSI and select line work as expected ...
Our project is to read the gyro (lis3dh) by using SPI communication.
Since the infocenter says that using nrf52832 for developing nrf52810 is okay.
We currently developed...
I have a client that's investigating BLE solutions to use in a future product. The rough specs they gave me include a TX power of +10dBm. The nRF52840 looks like a good option...
Hi,
In the BLE_UART example, I am trying to get some data about the time delay between the sending and the receiving of data between central and peripheral devices.
I...
I've been struggling with this for quite a while now. I've got a PCA10040 to spare that I am trying to use with nrf sniffer in Wireshark. I'm using a new iMac with the latest...
I have a problem I'm using nrf52840 DK. The task i want perform is start from idle state, wait for a button signal and the go out from idle, start with a loop where the code...
Hello ?
I was surprised that the program was organically well organized.
Based on the given installation manual, I completed the installation and corrected the program...
Hi!
We are using NRF52832 and NRF52840 with custom rf protocol.
I didn't found any information about time for applying new TXPOWER value of radio module.
Can I start...
Based on mesh sdk 3.1, open NRF_LOG_ENABLED in the light_switch_server example, ie NRF_LOG_ENABLED 1, the following error occurred during compilation: Linking light_switch_server_nrf52840_xxAA_s140_6...
I had two nRF52832 where one broadcasts with encrypted data of advertising beacon info and another nRF52832 should only scan without connecting and should decrypt the data...
Hello,
We are using nRF52832xx_aa controller for our product, the sleep current consumption is approx 2 uA @25 degree Celsius which is fine with me. But when the temperature...
We are writing SPI drivers for RF chip and blocked on the below issue. The issue we are facing is the Chip Select line is not active(active low) until the TX transaction is...
SDK: 12.3.0
SOFTDEVICE: s130_nrf51_2.0.1_softdevice
CHIP: nrf51822 AC 256K flash 32K ram
GCC flags:
# C flags common to all targets
CFLAGS += -DBOARD_CUSTOM
CFLAGS...
Hi,
I want to write or change the code in to nRF52832
I have some code this code i should write for nRF52832
kindly give any suggestion
here is the my code
uint8_t...
