I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Before updating firmware i have updated connection parameter with low connection interval. But it taking too much time. If I gave the same parameters at the first time while...
Dear sir.
This is jaykim from south KOREA.
I saw your company website about NRF2460 Chip.
Is this chip discontinue? It means not product any more??
Because We now...
Hei hi.
I'm developing simple beacon application with sdk 15.2, sd132 based on freeRTOS on nrf52832. The app and the whole project is built with help of ble_peripheral/ble_app_hrs_freertos...
void spi_read_write(0x1E,0x00) ==> output 0x10 as return value of register read.
Here I want to send value 0x90 as register value in the argument of spi_read_write(0x1E...
Hello, Looking for help in confirming what happens when pin 0.21 is grounded on the 810. I have a simple custom 810 based on the reference design with an added led and rgb...
I am using Keil uvision. Working with example codes, with uart example I got the code to send a data to mobile app through ble. But I cannot find code for receiving a data...
Hello All
I am working on nrf52810 and for programming i use segger studio in windows v7. And i refer nRF5 SDK 15.2.0. in my application use LM6BD temprature sensor connect...
SDK 15.2
I am wondering if anyone could point me in the right direction for optimal Timing configurations for the following parameters: 1. Advertising Interval 2. Scanning...
I am using the PWM app from nRF51_SDK_10.0.0_dc26b5e\components\libraries\pwm. I have loaded s110, and am running no other code.
The application hangs on the second cycle...
Hi
It seem that Nordic does not offer a service for delivering chips pre-programmed with a custom firmware?
We are currently having our boards manufactured in China and...
Hi there,
We are using the nRF52832 on our PCB design. We built the first batch and it was working fine, we built a second batch and all the boards are having issues.
...
Hello there.
I am new to Nordic and I want to make MAX30105 sensor to work with my NRF52 DK board (i am using the "nRF5_SDK_15.2.0_9412b96")...
I used the "twi_scanner...
Hi,
I am trying to make the two UARTEs from nRF52840 work at the same time, but I am facing some problems even with the examples found in the SDK. I am using the peripheral...
During development with the nrf52832 (SDK11.0.0-2.alpha), I occasionally get NRF_FAULT_ID_SD_ASSERT errors. I have a breakpoint set at the "softdevice_fault_handler" and the...
