I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi,
I am using the NVS to store my application data in the defined partition starting from a flash address of 0xFC000 to 0x100000.
I have 3 structures with variable sizes...
Interfacing mpu6050 with 52832 DK worked fine .
But when I used same sample code for 5340DK it produced errors .I configured device overlay file as below and build configuration...
Hi! I'm currently working on a project containing an nrf9160 as well as an nrf7002. I found the Nordic Distance Measurement Library, which is very exciting, and I was wondering...
I am currently struggling with the issue of the Bluetooth board disconnecting in irregular intervals ranging from 30 seconds to 10 minutes. The disconnection message is reason...
I kept getting the compile error when trying to build `sample/subsys/fs/fs_sample` ( github.com/.../fs_sample) to `nrf52840dk/nrf52840`.
```
C:/ncs/v2.8.0/zephyr/drivers...
Hi there,
I am working with NCS 2.9.0 and the nRF54L15-DK, running the radio test example with the RSSI Viewer, but it doesn't seem to be working.
Here are some error...
Dear nordic:
There is a problem while debugging the nrf52820 based on ncs v2.6.0
I wanna see the log via debug but failed, the circuitry is as the pic.How I can config...
HI,
We want to use NRF9151 to realize the DECT NR function. Now I have an NRF9151-DK in my hand, how to test the performance of DECT NR?
I used AT command to control NRF9151...
Hi nRF experts.
We built a module using nRF54L15, We are doing some verification. We need to do a distance test, so we need to set the tx power of the interval between advertising...
in my own board. I start a spi master.
and capture the signal of the CSN and SCK.
they looks abnormal
in one burst (package), the CSN has two pulse. I think the CSN...
I'm just using nRF24LE1 to make 2.4G wireless mouse, mouse sensor is PAW3205DB-TJ3T. But i got a problem, PAW3205DB-TJ3T uses two-wire spi(SCKL+SDIO), nRF24LE1 only supports...
I am trying to do an OTA update of the firmware on my device. I am using Nrf Connect SDK 2.1. I followed some of the tutorials and setup the device to advertise the SMP UUID...
I am using the VSCode extension (2024.12.55), nRF Connect SDK ( 2.9.0). I created a new project from the USB loopback sample to investigate how to configure a project for...
Hi,
I suddenly started getting MPSL ASSERT: 112, 2134 upon BT enable and upon research came across this post ( link ) and used following code:
HFXO starts on peripheral_lbs...
Hi,
We are developing a new project using the nRF52832 as our controller and nRF5 SDK 17.0.2 as our SDK.
We have integrated the NUS client and NUS peripheral parts from...
