Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Toolchain v2.70, SDK v2.7.0, VS Code, Windows
I am trying to enable the watchdog in my application, and I can successfully locate the device node and add a timeout, but...
Hi,
I am trying to figure out a way to update the toolchain and SDK for an nRF Connect for VS Code installed on an offline machine, without much success.
From https:/...
Hello,
I am working with the NRF9151 DK on DECT NR+ and I want to change the subcarrier scaling factor and subslot value in the hello_dect example. However, I am not sure...
NRF Connect SDK (v2.8.0), VS Code, NRF52840
Hi, while reading the Zigbee documentation I saw the following note:
"Support for Zigbee R22 has been deprecated in nRF Connect...
I am simply trying to build the hello world (and blinky, results are the same) with NRF-SDK 1.8.0 - it's based on Zephyr 2.7, which is the LTS release.
Target board is 5340...
Hi,
We are planning a new project that needs to use very low power. Since relay mode uses more power than simple node, can we turn off relay mode on all nodes until an event...
Hi, I am developing BLE beacon application on the nrf52820 soc which has limited Flash resources. I want to have the FOTA through BLE abilities built in to enable firmware...
Hi! Can you please help me identify what is causing this issue and/or provide more info about this:
[00:04:23.038,330] \033[1;31m<err> bt_sdc_hci_driver: SoftDevice Controller...
Hello everyone!
I'm working with the nRF52840 microcontroller and I wanted to get a bluetooth antenna and since I know that the whole RF thing is very complicated, I was...
Hi.
I have a custom board with a NRF9161. The nrf91's LTE block connects to the sim holder through a NX3DV2567HR switch and an TPD3F303DQDR ESD protection.
I'm using...
Hello there, Describe the bug When setting a breakpoint inside an IRQ handler in my application, I'm experiencing the following crash each time I try to continue, step over...
I am working on integrating an external antenna with the EYSHSNZWZ BLE module from Taiyo Yuden, which uses Nordic’s nRF52832 SoC . The biggest problem is that I cannot confirm...
Hello. I have designed in the nRF52840 into a product and we've seen this issue on at least two prototypes. The RESET pin seems to get stuck low (grounded) and I can't seem...
